Fish House Build #2

[BunchOfish]

Weekend update,  I managed to get the door installed and the plywood put on for the roof.  I had time to install the rubber but it was a little cool(54 degrees).  I would like to install it when its a bit warmer out so it relaxes a little better.  Hopefully the tin comes in later this week so I can get it installed this weekend.

[BunchOfish]

Well if it would ever stop raining maybe I could get the roof installed.  At least in the mean time I have gotten some wiring ran. 

[BunchOfish]

The roof is finally on and I got some of the wiring started.  The tin came in over the weekend so I was able to pick that up last night.  I will start to put that up this week if the weather permits.

[BunchOfish]

Made some good progress last night.  I managed to get the back tin put up.  Should be able to get the front started tonight.

 

[rl_sd]

Any slope on your roof?

[BunchOfish]

1 hour ago, rl_sd said:

Any slope on your roof?

Nope its flat!

[BunchOfish]

The front tin is on.

[BunchOfish]

I finally finished the tin today.  I even got the rear lights hooked up.

[BunchOfish]

I got all the wiring ran yesterday.  I can start insulating this week.  I will be using the 1.50" thick pink foam board.  The plan right now is to have everything wrapped up by November and I will deliver it when I go up north for firearms season(Nov 9th).

[leech~~]

Must have had a storm?  Good thing that big branch didn't wipe out the project! 

[BunchOfish]

1 hour ago, leech~~ said:

Must have had a storm?  Good thing that big branch didn't wipe out the project! 

No Actually I cut it down.  I had to so I could park my fish house in place of my boat this winter.  It was too low so it had to go.  Plus it was hanging out over my garage pretty far.  Its also a lot less leave I will have to deal with in a few weeks haha!

[BunchOfish]

Build update!  Things were put on hold last week as I had to do some repairs to my truck.  I got all the wiring finished up yesterday and I started putting up the insulation.  The plan is to get it fully insulated this week so I can start putting up paneling and T&G.  I will have more pictures as I get a little further along.

[Mike89]

1 hour ago, BunchOfish said:

Build update!  Things were put on hold last week as I had to do some repairs to my truck.  I got all the wiring finished up yesterday and I started putting up the insulation.  The plan is to get it fully insulated this week so I can start putting up paneling and T&G.  I will have more pictures as I get a little further along.

 

darn truck anyway!!!  

[BunchOfish]

I finished up the insulating last night.  Depending on the weather the next few days I might try and pick up the T&G and paneling.  I have a wedding on Saturday so a good part of my day will be used up and I might be hunting on Sunday(got a pretty nice buck hanging around). So far I'm sitting pretty good to have it done by November.

[BunchOfish]

Here are a few pictures. I started putting the T&G up on the ceiling. All the lights are led.

[leech~~]

Nice work.  Has the uncle ever came by to check on your work yet? 

[BunchOfish]

16 hours ago, leech~~ said:

Nice work.  Has the uncle ever came by to check on your work yet? 

Yeah he was down a few weeks ago and checked it out.

[BunchOfish]

Much progress was made today. All the T&G is up. Tomorrow the FRP will be going up.

[BunchOfish]

FRP is going up.  Starting to look really nice.

[BunchOfish]

I got another panel up tonight.  I also starting doing a little trim work on the side that is ready for it.  Looking good.

[leech~~]

Dang, you just night finish by Deer Hunting yet!

[BunchOfish]

9 hours ago, leech~~ said:

Dang, you just night finish by Deer Hunting yet!

Yeah that's the plan.  My uncle owns a bunch of land over in Wisconsin and would like to use it for their season so the pressure is on me to get it done.

[BunchOfish]

I got the cabinets up.  Now i just need to make the doors.  The end is in sight.

[leech~~]

Nice work. I could may be afford one, if I just stopped buying so many other toys!

[BunchOfish]

Things keep moving along.  I got a couple doors made for the cabinets and got the hole cut and hole covers installed.  I also finished filling nail holes with putty so a little sanding and it will be ready for some stain.

Edited October 18, 2019 by BunchOfish