Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. ?

Marvel Mystery Oil


Recommended Posts

Does anyone know if this stuff is any good? I bought a quart to add to the crankcase when I change my oil tomorrow. My Tahoe takes 6 quarts oil, so I figured instead of buying a 6th quart of oil for almost 4 bucks I would just use a quart of marvel for the same price.

Link to comment
Share on other sites

The stuff has been around for over 85 years and people still use it. I have never used it in my truck but I put a little in my small engines when I change there oil. I use synthetic in my truck so I don't know if there would be any benefit using MMO in that.

Link to comment
Share on other sites

Don't see the point of this unless you are trying to clean things out. If you have maintained the engine and kept up on oil changes there should be no need for it. MMO is going to provide less lubrication than an equivalent amount of engine oil.

Link to comment
Share on other sites

From what I have been able to find out, it is correctly named, "Mystery Oil."

Marvel goes out to any and all oil companies to buy 'clean-out' (when an oil manufacturer changes the filling machinery from one product to another the left over in the lines usually can't go as either product but is scrap) oil and anything else they can get for pennies on the dollar. Marvel then takes and mixes it all together, using any primarily ATF as a viscosity control component getting it to the approximate viscosity they want. The mix then is truly a mystery - a combination of who knows what (and they don't know either) of engine oils, gear lubes, transmission lubes, industrial and commercial lubes, hydraulic lubes and more.

I can't think of anything of mine I would trust to put this in.

Link to comment
Share on other sites

i use it on my sleds.. i usually add a bit to every tank of gas and watch the temp gauge.. if the oiler quits i have a miniscule ammount of oil to keep it lubed till i notice the temp is going up. ive used it in small engines such as snow blowers and tillers and in my opinion it works GREAT for removing junk and sludge from motors..

Link to comment
Share on other sites

I works well for removing moisture from the crankcase of a sunken 4-wheeler. 2 oil changes, half MMO half engine oil and they are ready to hit the mud again! Other than that Ive never seen it used for anything, every shop has a can on the shelf though!

Link to comment
Share on other sites

We used to use MMO to spray on sheets of aluminum to help lubricate turret press punches when punching close proximity hits at a high speed. It would help in keeping the punches from galling up and tearing the .080" material between hits.

A couple issues we ran into was 1) it wasn't compatible with our wash system for our powder paint line and 2) it gummed up the conveyor belts on our deburring machines and transfer that onto parts.

I don't know this for sure without looking at an MSDS, but I have been told that MMO has parafin wax in it.

Link to comment
Share on other sites

Join the conversation

You can post now ↓↓↓ or ask your question and then register. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Your Responses - Share & Have Fun :)

    • got this tackled today took about 3 hours to get both sides done. Didnt even get to use a torch....   Thought I was golden with just jacking it up and I could get to everything but no luck. Had to remove the entire axle hub and brake assembly to get to what I needed. Was a pain but still better then taking off the entire pivot arm.    Axle bearings were already greased and in great shape thankfully. Got both leaf springs installed and its ready for the road again.   Probably going to have my electric brakes checked, I am not touching anything with the brake drums. Based on what I saw it doesn't look like my electric brakes have been working anyway. Brakes are nice to have if its slippery out
    • By The way that didn't work either!! Screw it I'll just use the cellular. 
    • It’s done automatically.  You might need an actual person to clear that log in stuff up.   Trash your laptop history if you haven’t tried that already.
    • 😂 yea pretty amazing how b o o b i e s gets flagged, but they can't respond or tell me why I  can't get logged in here on my laptop but I can on my cellular  😪
    • I grilled some brats yesterday, maybe next weekend will the next round...  
    • You got word censored cuz you said        B o o b ies….. haha.   Yeah, no… grilling is on hiatus for a bit.
    • Chicken mine,  melded in Mccormick poultry seasoning for 24 hours.  Grill will get a break till the frigid temps go away!
    • we had some nice weather yesterday and this conundrum was driving me crazy  so I drove up to the house to take another look. I got a bunch of goodies via ups yesterday (cables,  winch ratchet parts, handles, leaf springs etc).   I wanted to make sure the new leaf springs I got fit. I got everything laid out and ready to go. Will be busy this weekend with kids stuff and too cold to fish anyway, but I will try to get back up there again next weekend and get it done. I don't think it will be bad once I get it lifted up.    For anyone in the google verse, the leaf springs are 4 leafs and measure 25 1/4" eye  to eye per Yetti. I didnt want to pay their markup so just got something else comparable rated for the same weight.   I am a first time wheel house owner, this is all new to me. My house didn't come with any handles for the rear cables? I was told this week by someone in the industry that cordless drills do not have enough brake to lower it slow enough and it can damage the cables and the ratchets in the winches.  I put on a handle last night and it is 100% better than using a drill, unfortatenly I found out the hard way lol and will only use the ICNutz to raise the house now.
  • Topics

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.