Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. ?

Mower needed


perchking

Recommended Posts

Well the 42” 14 year old craftsman LT1000 is heading to the hunting camp so I need a new one for Home. I cut about 2 acres with lots of tree so a zero turn only makes sense, looking 52 - 60” deck and have about a 5K budget to work with. Ariens ikon has me intrigued but also looking at a couple used stand up Wright’s with less than 200 hrs. Also looking at the z series. Thoughts? 

Link to comment
Share on other sites

I got a hustler raptor SD last year with a 54" deck. I cut about 2 acres also and my mowing time has be cut down by half.

I chose to go with a 54 instead of a 60 beside cause of uneven ground and road ditch. zero turns don't side hill very well

so if you have hilly ground I would try one out. I used two of my neighbors one was a john deere witch I like a lot and a country clipper

 I didn't like that one.  It had a joy stick that controlled the drive  I thought it was very touchy mowed my yard twice with it    

 

Link to comment
Share on other sites

I’ll second the Hustler recommendation.  I have a fastrak 54” and couldn’t be happier. Put about 350hrs on the last 4 years. Had a 42” JD before this one, and darn near cut my mowing time in half. If you got the hustler route, get the front flex springs.... they ar worth the money

Link to comment
Share on other sites

I don’t have any experience with the Hustlers so I can’t compare them.  I picked up a used Z track with a 60 inch deck and am glad I did.  I mow probably 3 acres though and a lot of it is a flat meadow as we call it.  It’s the bomb out there.

 

When I get up closer to the house and have contours and trees it gets a little tougher.  The front left deck wheel sometimes gouges into the turf if I turn too sharp in certain spots and getting between some trees is a challenge with the 60.  If I didn’t have the big flat to mow I’d look for a 54.

 

Either way, don’t turn truly zero turn your zero turn.  You’ll twist a hole in your turf if you don’t keep that pivot wheel turning at least a little bit.

 

Other thing to note: I added a power flow bagger with 3 bags for fall clean up.  It’s a life saver IMO.  But it doesn’t clean as well as the (2) bagger on the 48 inch rider.  That thing is like a vacuum but it takes way longer due to dumping frequency.

 

To do it over again I would consider a tow behind bagger for the fall but still don’t know if I’d want to use that for regular mowing.

Edited by Wanderer
Link to comment
Share on other sites

I have a toro titan 48 inch and mow about 2 acres. I thought I wanted a bigger one but found a deal on c-list that was too good to pass up. The bigger you get the more scalping can happen. I love mine and takes about an hr to mow so not terrible. Lots of good brands out there, the motor is what you need to pay attention too. You pay more for the higher end motor but should last that much longer. I agree you never turn on a dime or your ruining your lawn. 3 pt turns is the only way. If you want to be fancy get a striping kit. Looks awesome. Those are standard on simplicity’s. 

Link to comment
Share on other sites

the place I bought my raptor SD at didn't have a limited to look at.
The big thing is the deck. I thought the sd had a heaver deck then the raptor.

looks like the limited has some of the nice options that the sd has.

The flex forks would be nice 

Link to comment
Share on other sites

Join the conversation

You can post now ↓↓↓ or ask your question and then register. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Your Responses - Share & Have Fun :)

    • As a recovering machinist, I can appreciate that.  If the spec is 0.001 - 0.0015, then clearly the correct measurement is 0.00125, duh…
    • I just figured that it is easy enough to just get a 3 bank so when the boat is not in use I can keep all 3 batteries charged. I have not bough a charger yet, maybe I will give it some more thought. Edit: After thinking this over, with the size, weight, and heat output of the charger (as well as the cost) I think it makes sense to just buy a 2 bank charger, I have a smaller charger i can use on the starting battery when the boat is sitting at home. Forgive me, for i am a retired engineer and I have to obsess over everything...
    • Congrats on the motor!  I think you’ll like it.   I can’t say much on the charger location but I’ve seen them under the lid in back compartments and under center rod lockers.  160 degrees is more than I expected to hear.   Curious why you’re opting for a 3 bank charger with a 24V trolling motor.  Unless you don’t feel you be running you big motor enough to keep that battery up as well?
    • I did buy an Minnkota Ulterra, thanks for the recommendations. I had a bunch of Cabela"s bucks saved up, which helped. Now i need to get an onboard battery charger. Where do you guys mount these things in your boat? The manufacturer I am looking at {Noco genius) says tht their 3-bank charger will run at 160 degrees, seems like a lot of heat in an enclosed compartment? Thanks for any input on this.
    • You're very lucky a troop of Sea Monkey's didn't carry you away.   
    • Wasn't terrible at a state park beach. Antelope island maybe.  I wouldn't recommend it as a beach destination tho.  Figured I was there, I'm getting in it.
    • The water looked and smelled disgusting with hundreds of thousands of birds sh*tting in there.  About as gross as the Salton Sea. When I duck hunted there I didn't even want to touch the water.
    • It's kinda gross with the algae in the summer but I got in it anyway.  Wanted to see the increased bouyancy at work.  You can kinda tuck yourself into a ball and you'll just float with your head above water.  When dry off you look diamond encrusted with the salt.
    • We went to the flats too. I dipped a tire on the rental car onto it just to say I’ve been there,but it was still pretty soft from winter melt. After seeing some moron in a BMW suv get dragged out of the muck I had no intention of repeating his stupidity. 
    • I've been out on the flats. It's like being on a different planet 
  • Topics

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.