Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. ?

Trailer Tires


loadmaster

Recommended Posts

Having wear problems in the last month on boat trailer. Specs, Bear Trailer with a Max Load of 2670 with 205/75D tires. Carrying a 17.5 G-3 with a 115 4 stroke Yaammie. Take a look at the wear Right side is going bald on inside and outside with no wear on center tread. Left side has a wear pattern I have never seen. Maybe some tire expert can help out. Keep tires at 50lbs. I have always had terrible tire wear on this trailer but never this bad. full-837-48937-010.jpg

full-837-48938-009.jpg

Link to comment
Share on other sites

The tire wear is called "checking" which means the steel belts are separating on the interior. Its caused sometimes by over inflation or poor quality tires. Get these replaced asap as the belts can come through the tire and cause a quick flat with bad consequences.

Link to comment
Share on other sites

I have had two brand new trailers manufactured by Shore Lander and experienced the same problem with the tires as you on THE FIRST TRAILER that I owned. I don't think it had anything to do with the trailer. I think it was all about the tires and proper inflation. I don't remember the brand of tires (NOT CARLISLE)on the first trailer but I think they were good quality as that is what Shore lander usually puts on their trailers. I think it was inflation because I tended to under inflate the tires to make it ride better. The most recent trailer from Shore Lander was purchased in 2002 and I still have one of those tires still on the ground. IMO, not a good idea and I will change that out to make it a spare this fall. I watched a video on tire life and was surprised that they recommended a six year tire life on passenger cars. So it should be longer on tires that are only used 6-7 months of the year??? Wrong. Even though that tire is not being used, it is aging

I have been pleased with Goodyear Marathons and one of the tires (old)that is on the ground was made in Canada and the other made in China. I was a little concerned that the tire made in China might be a dud but so far so good. They must be made to Goodyear specifications before they will put their stamp on the tire.

Wheel bearing issue causing the problem??? Maybe, but if you use Bearing Buddy's(SP)and the bearing is too loose, my experience has been the wheel will kick out the Buddy to the tune of $15.

Axle alignment?? Maybe, but I would think one side would be wearing a lot different than the other and you can measure the distance from the axle to the end of the trailer to check for correct alignment.

I hope this helps.

Mike

Link to comment
Share on other sites

Ya 50psi is recommended. I know see this whole tire is messed. One poster over inflated some under bad brand. Did measure the axle different points and its not the axle. Checked bearings fine. I think I am going to buy some name brand tires with a bigger load range than D get a digital pressure gauge and check every time rig is moved. Thanks for the input.

Link to comment
Share on other sites

Load I had the same issue with my carlisle tires. Got rid of that junk and got some good radials at Duluth Tire and 2 years later not 1 issue.

Same Here!!!

Went in and told them about my wear problems and what they would recommend. Think I am going on 4 or 5 years with no problems.

Link to comment
Share on other sites

Join the conversation

You can post now ↓↓↓ or ask your question and then register. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Your Responses - Share & Have Fun :)

    • As a recovering machinist, I can appreciate that.  If the spec is 0.001 - 0.0015, then clearly the correct measurement is 0.00125, duh…
    • I just figured that it is easy enough to just get a 3 bank so when the boat is not in use I can keep all 3 batteries charged. I have not bough a charger yet, maybe I will give it some more thought. Edit: After thinking this over, with the size, weight, and heat output of the charger (as well as the cost) I think it makes sense to just buy a 2 bank charger, I have a smaller charger i can use on the starting battery when the boat is sitting at home. Forgive me, for i am a retired engineer and I have to obsess over everything...
    • Congrats on the motor!  I think you’ll like it.   I can’t say much on the charger location but I’ve seen them under the lid in back compartments and under center rod lockers.  160 degrees is more than I expected to hear.   Curious why you’re opting for a 3 bank charger with a 24V trolling motor.  Unless you don’t feel you be running you big motor enough to keep that battery up as well?
    • I did buy an Minnkota Ulterra, thanks for the recommendations. I had a bunch of Cabela"s bucks saved up, which helped. Now i need to get an onboard battery charger. Where do you guys mount these things in your boat? The manufacturer I am looking at {Noco genius) says tht their 3-bank charger will run at 160 degrees, seems like a lot of heat in an enclosed compartment? Thanks for any input on this.
    • You're very lucky a troop of Sea Monkey's didn't carry you away.   
    • Wasn't terrible at a state park beach. Antelope island maybe.  I wouldn't recommend it as a beach destination tho.  Figured I was there, I'm getting in it.
    • The water looked and smelled disgusting with hundreds of thousands of birds sh*tting in there.  About as gross as the Salton Sea. When I duck hunted there I didn't even want to touch the water.
    • It's kinda gross with the algae in the summer but I got in it anyway.  Wanted to see the increased bouyancy at work.  You can kinda tuck yourself into a ball and you'll just float with your head above water.  When dry off you look diamond encrusted with the salt.
    • We went to the flats too. I dipped a tire on the rental car onto it just to say I’ve been there,but it was still pretty soft from winter melt. After seeing some moron in a BMW suv get dragged out of the muck I had no intention of repeating his stupidity. 
    • I've been out on the flats. It's like being on a different planet 
  • Topics

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.