Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. ?

  • 0

'99 Mercury 90hp problem....HELP!


blakjack23

Question

Hi everyone, I decided to take the boat out last night to get some fishing in but it didn't turn out too well. I launched the boat, started the engine as usual, slowly left the launch and about 50 yards out it died. After that I could start it, but anytime I put it in gear and gave it a little gas it died again. I could also start it while having the throttle on full (out of gear of course), it would start and right when it would start getting rev'd high I would pull back on the throttle and it would die again. The bulb it hard and water is coming out of the pee hole. There is also plenty of gas and oil. Any idea's? She has been running great all summer until now.

Link to comment
Share on other sites

8 answers to this question

Recommended Posts

  • 0

My buddies dad has a 75 merc and his motor does the exact same thing until warmed up good. We have to sit at the landing for a good 5-10 min letting it warm up before we can think of taking off.

Sounds dumb, but did you give it plenty of time to warm up? With the summer winding down, the water is colder along with the air temps and it might take an extra few minutes to get up to operating temps.

Link to comment
Share on other sites

  • 0

I would say fuel starvation, could be dirty carbs or bad fuel pump. Try to start it and see if it keeps running while pushing key in (choke).

If it gets better then your carbs needs cleaned or rebuilt.

Link to comment
Share on other sites

  • 0

Check the fuel filter, check spark, etc.

Also make sure you don't have water in your gas. I had a problem this summer with my boat starting on full throttle and then cutting out as I dropped the RPM's down. I was suspecting the carbs, but turns out I had a bunch of water at the bottom of the tank. Too bad the dealer figured that one out!

Link to comment
Share on other sites

  • 0

WHAT KIND OF GAS DO YOU USE? TRY PREIMIUM AND ADD A CAN OF SEA FOAM TO 20 GALS OF GAS OR HALF CAN TO 10 GAL OF GAS I DO THIS WITH MY 2002 9O AND SHE RUNS LIKE A TOP YOU WILL NOTICE TOP END IS MUCH BETTER TWO. GOOD LUCK. DAN

Link to comment
Share on other sites

  • 0

Does it come to life when you hit the choke just before it dies? I have a merc 90 2002 model. Does the same thing. Been to the shop for a checkup. All was fine. I concluded its just cold blooded! Mine comes to life when i hit the choke! sure is irritating specially when the ramp is busy!!

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.


  • Your Responses - Share & Have Fun :)

    • we had some nice weather yesterday and this conundrum was driving me crazy  so I drove up to the house to take another look. I got a bunch of goodies via ups yesterday (cables,  winch ratchet parts, handles, leaf springs etc).   I wanted to make sure the new leaf springs I got fit. I got everything laid out and ready to go. Will be busy this weekend with kids stuff and too cold to fish anyway, but I will try to get back up there again next weekend and get it done. I don't think it will be bad once I get it lifted up.    For anyone in the google verse, the leaf springs are 4 leafs and measure 25 1/4" eye  to eye per Yetti. I didnt want to pay their markup so just got something else comparable rated for the same weight.   I am a first time wheel house owner, this is all new to me. My house didn't come with any handles for the rear cables? I was told this week by someone in the industry that cordless drills do not have enough brake to lower it slow enough and it can damage the cables and the ratchets in the winches.  I put on a handle last night and it is 100% better than using a drill, unfortatenly I found out the hard way lol and will only use the ICNutz to raise the house now.
    • I haven’t done any leaf springs for a long time and I can’t completely see the connections in your pics BUT I I’d be rounding up: PB Blaster, torch, 3 lb hammer, chisel, cut off tool, breaker bar, Jack stands or blocks.   This kind of stuff usually isn’t the easiest.   I would think you would be able to get at what you need by keeping the house up with Jack stands and getting the pressure off that suspension, then attack the hardware.  But again, I don’t feel like I can see everything going on there.
    • reviving an old thread due to running into the same issue with the same year of house. not expecting anything from yetti and I already have replacement parts ordered and on the way.   I am looking for some input or feedback on how to replace the leaf springs themselves.    If I jack the house up and remove the tire, is it possible to pivot the axel assembly low enough to get to the other end of the leaf spring and remove that one bolt?   Or do I have to remove the entire pivot arm to get to it? Then I also have to factor in brake wire as well then. What a mess   My house is currently an hour away from my home at a relatives, going to go back up and look it over again and try to figure out a game plan.           Above pic is with house lowered on ice, the other end of that leaf is what I need to get to.   above pic is side that middle bolt broke and bottom 2 leafs fell out here is other side that didnt break but you can see bottom half of leaf already did but atleast bolt is still in there here is hub assembly in my garage with house lowered and tires off when I put new tires on it a couple months ago. hopefully I can raise house high enough that it can drop down far enough and not snap brake cable there so I can get to that other end of the leaf spring.
    • Chef boyardee pizza from the box!
    • Or he could go with leech~~~~~
    • Bear can relate too. Tell Leech to start a new account named Leech5, we'll know who he is.If he has any trouble, Bear can walk him through it.
    • Blessed Christmas to all.  
  • Topics

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.