Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. ?

muzzy broadheads


roosterslayer

Recommended Posts

I shot a buck 2 years ago with a 3 blade muzzy....it killed it but I also cut my hand on one of the blades. I dont like how they are all seperate blades and thats how I cut my hand pretty good....because a blade broke off. It did its job....but unluckly I cut myself

Link to comment
Share on other sites

I shoot three blade 125 grain muzzys,and have only broken one and that was a spine shot.They fly well and have a good cutting edge.Have had a few bad shoulder hits over the years and have not broken one there.Four blade could be real good but no need to change as the three have done just fine for me.

Link to comment
Share on other sites

I have shot muzzy's for about the last 10 years and still love them, I like the 4 blade 90 grain, complete pass-throughs about 8 out of ten times. They fly consistant and you can use the practice blades for practice. No complaints here.

Link to comment
Share on other sites

In my opinion, the best head out there. I have shot several deer with them, and had excellent results. I have never had a blade fall out or break and have had all pass throughs. BTW I shoot 125 gr 3 blades.

Link to comment
Share on other sites

Muzzy makes an excellent blade, and the chisel tips are a nice touch. If you are looking to decide between a 3 or 4 blade, I would probably go with a 3. 4 blades will shoot fine with most setups, but can increase any problems you might be experiencing as far as planing out goes. Only way to find out is to fire a few with practice blades.

Link to comment
Share on other sites

Just switched from Thunderheads in year's past to Muzzy's last year. All of my friends swore by them, so when I bought a different bow, I figured that would be the best time to try them. Flew great and got complete pass through, from the top of the back down on a steep angle shot. No complaints and no intention to switching back. (3 blade 100gr.)

Link to comment
Share on other sites

I also have shot the Muzzy 3 blade 100 gr for the last few years, I like the head but I am looking at the G5 Montec

I just think this head will last longer than the Muzzy.

I have never shot the practice blades either, thus the Muzzy is hard on "The Block"

http://www.g5outdoors.com/main/Default.aspx

Link to comment
Share on other sites

I used to shoot mechanical broadheads, but when i failed to penetrate the deer many times, I switched to muzzy 100 grain 3 blades. I have had no problem with them and absolutely love them. I would strongly recommend them.

Link to comment
Share on other sites

I was thinking about switching over to fixed blades (muzzy) this past fall, but after I shot with em'- my pattern was off big time.

I think it really depends on the arrow you shoot and if it is able to hold up with a fixed blade. Not every arrow shoots the same.

I shoot mechanicals and got my first deer this year. Actually looked at the mark I made and all 3 blades opened up- could see it by the cut I made through the deer cool.gif

Link to comment
Share on other sites

I couldn't get the muzzy to fly right either! I gave them away, and went back to my NAP Spitfires. I have never had any problems with them. Now I use the new cut on contact tip! Love it! 2 pass threws this fall!

My .02 cents

Link to comment
Share on other sites

I agree WB...if you can't shoot Muzzy's strait then your bow is out of tune. You may not notice it with field points or spitfires...but it is slightly out of tune. Not saying you should change, I used spitfire's a couple of years and had good luck, what ever works! cool.gif

Link to comment
Share on other sites

I don't think it was because my bow wasn't tuned right. I just bought my Outback before this last season,and the guy at the proshop took the time to tune it perfectly. He has learned how to set'em up from the guys at the factory. He even took the time to write down every measurement so if I ever needed it worked on he could put back to wear it shoots the best if I screwed with it. So maybe you think the bow is out of tune,but I don't think that was the problem. The Muzzy always wanted to go down and left. I could have adjusted my pins for this, but then my field points were off. So I chose to shoot the mechanicals so it was the same as my field points. There are very few guys I trust to work on my equipment, or to know what they are talking about when it comes to hunting, I am sure you guys are the same. For me the guy that set-up my bow is one of those guys. He only works on Mathews, so I think he knows how to set them up. And hey, if Muzzy works for you I am happy you found a broadhead you have faith in....I don't, no big deal!

Link to comment
Share on other sites

Hey guys and gals, the reason I brought up the topic is because I plan on sticking ol blackie with an arrow this fall and have heard great things about muzzy. I was also looking at the spitfires as well but I have had a few friends that didn't have good luck with mechanicals on the long hair that bears have. Just looking for some good advise from the people that use the products.

Link to comment
Share on other sites

I've heard a few horror stories about mechanicals that don't open up on sharp angled shots, but i shoot them myself and haven't had any problems. The first deer I shot with a spitfire was a young buck, quartering away from me, and I think the arrow might have even skipped a little farther forward before exiting. That broadhead absolutely destroyed the shoulder blade on the way out, catching both lungs and snapping the shoulder blade nearly in half- who needs a rifle smirk.gif! The deer made a half-circle around my tree and died 40 yards away-that was enough to convince me of the punch those babys are packing grin.gif

Personally, the two fixed blade models I would be interested in trying would be the re-introduced razorbacks, and the one piece, 3-blade that doesn't have any removeable parts (can't remember the name off the top of my head). Anyone got any feed back on those tips?

Link to comment
Share on other sites

Illtake check my previous post, I like the look of the G5 Montec.

Something also to ponder, your bow can be tuned for perfection and still have bad broadhead flight. You also have to tune each arrow with its head.

Even more so with the cabons

Link to comment
Share on other sites

Quote:

I sense a thread drift, should we start a post on

How to tune a Broadhead


Didn't mean to drift here crazy.gif

My bow is tuned perfectly. I shoot tight groups with field tips and my mechanicals. Everything was high and to the left with the fixed blade (muzzy).

To each is own I guess and if it works for you-stick with it!

Link to comment
Share on other sites

Yea, I didn't mean to ruffle any feathers by saying bows weren't tuned. I was assuming that the muzzy's were flying all over the place. If they shoot the same time in and time out then your bow is tuned. My bow shoots them about 5 inches low everytime...so I adjust my sights and go with it. The only reason that I switched to Muzzy's was the penatration issue that I found with spitfires. But a well placed shot will work with any broadhead, thats the facts.

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.


  • Your Responses - Share & Have Fun :)

    • By The way that didn't work either!! Screw it I'll just use the cellular. 
    • It’s done automatically.  You might need an actual person to clear that log in stuff up.   Trash your laptop history if you haven’t tried that already.
    • 😂 yea pretty amazing how b o o b i e s gets flagged, but they can't respond or tell me why I  can't get logged in here on my laptop but I can on my cellular  😪
    • I grilled some brats yesterday, maybe next weekend will the next round...  
    • You got word censored cuz you said        B o o b ies….. haha.   Yeah, no… grilling is on hiatus for a bit.
    • Chicken mine,  melded in Mccormick poultry seasoning for 24 hours.  Grill will get a break till the frigid temps go away!
    • we had some nice weather yesterday and this conundrum was driving me crazy  so I drove up to the house to take another look. I got a bunch of goodies via ups yesterday (cables,  winch ratchet parts, handles, leaf springs etc).   I wanted to make sure the new leaf springs I got fit. I got everything laid out and ready to go. Will be busy this weekend with kids stuff and too cold to fish anyway, but I will try to get back up there again next weekend and get it done. I don't think it will be bad once I get it lifted up.    For anyone in the google verse, the leaf springs are 4 leafs and measure 25 1/4" eye  to eye per Yetti. I didnt want to pay their markup so just got something else comparable rated for the same weight.   I am a first time wheel house owner, this is all new to me. My house didn't come with any handles for the rear cables? I was told this week by someone in the industry that cordless drills do not have enough brake to lower it slow enough and it can damage the cables and the ratchets in the winches.  I put on a handle last night and it is 100% better than using a drill, unfortatenly I found out the hard way lol and will only use the ICNutz to raise the house now.
    • I haven’t done any leaf springs for a long time and I can’t completely see the connections in your pics BUT I I’d be rounding up: PB Blaster, torch, 3 lb hammer, chisel, cut off tool, breaker bar, Jack stands or blocks.   This kind of stuff usually isn’t the easiest.   I would think you would be able to get at what you need by keeping the house up with Jack stands and getting the pressure off that suspension, then attack the hardware.  But again, I don’t feel like I can see everything going on there.
    • reviving an old thread due to running into the same issue with the same year of house. not expecting anything from yetti and I already have replacement parts ordered and on the way.   I am looking for some input or feedback on how to replace the leaf springs themselves.    If I jack the house up and remove the tire, is it possible to pivot the axel assembly low enough to get to the other end of the leaf spring and remove that one bolt?   Or do I have to remove the entire pivot arm to get to it? Then I also have to factor in brake wire as well then. What a mess   My house is currently an hour away from my home at a relatives, going to go back up and look it over again and try to figure out a game plan.           Above pic is with house lowered on ice, the other end of that leaf is what I need to get to.   above pic is side that middle bolt broke and bottom 2 leafs fell out here is other side that didnt break but you can see bottom half of leaf already did but atleast bolt is still in there here is hub assembly in my garage with house lowered and tires off when I put new tires on it a couple months ago. hopefully I can raise house high enough that it can drop down far enough and not snap brake cable there so I can get to that other end of the leaf spring.
  • Topics

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.