Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. ?

getting out line twist


catflisher

Recommended Posts

what i have found to work for twist is to run 20 to 30 feet of line out(if thats as deep as i'll be flisHing)and run the line tru an old piece of inner tube materael once or twice...do it every time after i get back from a trip or before i go our...makes a big difference in how line comes off the reel and how bait reacts once its down there....smart fish don't like spinning bait....finnally figued out how to work this thing,by accident and have been waiting to get on...hello flishermans and womans....

Link to comment
Share on other sites

The quickest and easiest way that I have found to remove line twist is to drag the line behind me with the boat moving at a slow speed. Don't leave anything on the line, not even a snap. By the time you have released the amount of line you want to straighten it's already done and you can begin to reel it back in. Reel slowly so the line continues to unwind with you.

I can usually complete my entire spool in less than about 2 minutes. By doing the entire spool I find it also helps give the portion of line you rarely use a chance to get off the spool and lose some memory. Afterwards I get better smoother casts too.

Bob

Link to comment
Share on other sites

I use the same method as BobT ,,having the line wet when reeling it back up helps seat the line on the spool better too,,,A few years ago I was trolling to get the twist out on 4 rods at the same time when I was approached by the DNR ,,,shocked the dickens out of them when they had me pull up my lines and had nothing on the other end ,,suprisingly having all the line out puts a pretty good bend in the rod

Randoid

Link to comment
Share on other sites

I have found that an piece of old boot leather works better then the innertube rubber.(This is a method used by fly fishermen to straighten the tippets on their flyline!)

I use this in the winter. The other method works best in the summer.

Cliff

Link to comment
Share on other sites

here you go...pull out as much line as the depth you usually will be fishing,and a bit more...walk it out(you can finnally do this outside)place the line in a fold of rubber so you can lightly squeeze it,and go the length of the line holding it in the fold of the rubber.once is fine,twice is nice.you'll notice as you go along the line will really get twisty.that's the twist you'r taking out.

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.


  • Your Responses - Share & Have Fun :)

    • If you really want to treat your wife (and yourself) with a remote operated trolling motor, the Minn Kota Ulterra is about easy as it gets.  Auto stow and deploy is pretty awesome.  You just have to turn the motor on when you go out and that the last time you have to touch it.   24V 80lb.  60 inch shaft is probably the right length for your boat.  They ain’t cheap - about $3k - but neither one of you would have to leave your seat to use it all day.
    • Wanderer, thanks for your reply. I do intend for it to be 24 volt, with a thrust of 70-80. Spot lock is a must (my wife is looking forward to not being the anchor person any more).  With my old boat we did quite a lot of pulling shad raps and hot n tots, using the trolling motor. Unlikely that we will fish in whitecaps, did plenty of that when I was younger. I also need a wireless remote, not going back to a foot pedal. We do a fair amount of bobber fishing. I don't think I will bother with a depth finder on the trolling motor. I am leaning toward moving my Garmin depth finder from my old boat to the new one, just because I am so used to it and it works well for me. I am 70 years old and kinda set in my ways...
    • Dang, new content and now answers.   First, congrats on the new boat!   My recommendation is to get the most thrust you can in 24V, assuming a boat that size isn’t running 36V.  80 might be tops?  I’m partial to MinnKota.     How do you plan to use the trolling motor is an important question too.     All weather or just nice weather?   Casting a lot or bait dragging?   Bobber or panfish fishing?   Spot lock?  Networked with depth finders?  What brand of depth finders?
    • We have bought a new boat, which we will be picking up this spring. It is an Alumacraft Competitor 165 sport with a 90 horse Yamaha motor. I will be buying and installing a trolling motor,  wondering if I can get some recommendations on what pound thrust I will want for this boat?  Also, I will be selling my old boat, is there a good way to determine the value on an older boat ( mid-80's with a 75 horse 2-stroke  Mariner motor)  I will appreciate any help with these questions.
    • Sketti...  not out of a jar either!
    • Lol yeah I watched that
    • I went ahead and watched some of the MLF coverage.  Wheeler didn’t make the cut but the bigger story was the Poche/Avera fallout.   Kinda funny listening to both sides of the story and putting together the scenario, reading between the lines.
  • Topics

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.