Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. ?

Placement Of Rattle Reels


freezdried

Recommended Posts

I am getting ready to mount my rattle reels in my new fish house. Should I put them Knee high, waist high, or by the ceiling? They are Lindell Ice Rigs so they are removable when not in use. I have heard some folks say to mount them up high to keep them out of the way. What do you think?

Link to comment
Share on other sites

Ihad mine waist high but changed them after jiggin for eyes kept hitting them with the rod tip when I would set the hook. I found at a garage sale a couple of buzzer set ups that I,m going to try. I,ll try to get some pics on later.

Link to comment
Share on other sites

I'm not sure what brand mine are. I think their called Mille Lacs rattles, but they are the wood spindle ones with the bells in it. I got them at the BP gas station up at mille lacs next to trophys bar and grill. I like the wood ones because they seem to make more noise than the plastic ones. they do come apart with a plastic wing nut.

Link to comment
Share on other sites

Great topic, here goes. Thus far, nobody got this yet:

Ok, if you get the real deal Lewandoski rattle reels, like they sell on fish house supply or at Unclaimed Freight in Milaca, you can purchase or order EXTRA mounting brackets for them for a couple bucks, then you can have them mounted "high" during the day, and if you are sitting down, move em to a lower position. The little bracket is almost unnoticable on the wall-- most better bait shops sell the little bracket, the Lewandoski Rattle Reels just drop into them.

Hope I did not drop too many names there... my bad!

Link to comment
Share on other sites

I mounted mine on some swing arms on a hinge to move them when not in use. They are about thigh high. I have two others that are removable that use a socket and pin type setup that I take out for travel. I use small bungies to hold them against the wall when not in use. Here are how most of mine are mounted:

Rattlereelmount.JPG

Link to comment
Share on other sites

I preferr on the ceiling. That what you can place a marker at the rattle reel and see it easily when laying down and it is just easier to feed line set hook ect if you don't have to bend down to get at it.

Link to comment
Share on other sites

elwood i have a way to improve your buzzers.

cut a small notch in the rim of the reel with a hack saw...only a couple of mm deep. this will allow you to use a bobber rod instead of hand lining. you put the line of the bobber rod in the notch and and spin the reel until it is almost to the buzzing point but not quite. fish takes your bobber, spins the reel, sets off the buzzer and then you can fight it with the rod

if you like doing it by had cool, but if you like the rod better, thats the best way to go

Link to comment
Share on other sites

None are as good as the Original Lindells. I mount them high so they are not in the way. I just pull up on the line to jig them. You can also get extra wall bracket for them too. You can mount them to a bucket and use them for tip ups too.. Or that is handy when fishing outside.

Link to comment
Share on other sites

Place them high enough so they aren't in the way, and go with the Lindell Ice Rigs, they are by far the best rattle reel on the market. No wingnuts, no unwanted line vibration, and the smoothest spinning spool there is. The Lindell Ice Rigs are quality constructed and you get what you pay for. I also like the rod holders which are pretty ingenius in their own right for using with my spinning rods.

Link to comment
Share on other sites

Join the conversation

You can post now ↓↓↓ or ask your question and then register. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Your Responses - Share & Have Fun :)

    • got this tackled today took about 3 hours to get both sides done. Didnt even get to use a torch....   Thought I was golden with just jacking it up and I could get to everything but no luck. Had to remove the entire axle hub and brake assembly to get to what I needed. Was a pain but still better then taking off the entire pivot arm.    Axle bearings were already greased and in great shape thankfully. Got both leaf springs installed and its ready for the road again.   Probably going to have my electric brakes checked, I am not touching anything with the brake drums. Based on what I saw it doesn't look like my electric brakes have been working anyway. Brakes are nice to have if its slippery out
    • By The way that didn't work either!! Screw it I'll just use the cellular. 
    • It’s done automatically.  You might need an actual person to clear that log in stuff up.   Trash your laptop history if you haven’t tried that already.
    • 😂 yea pretty amazing how b o o b i e s gets flagged, but they can't respond or tell me why I  can't get logged in here on my laptop but I can on my cellular  😪
    • I grilled some brats yesterday, maybe next weekend will the next round...  
    • You got word censored cuz you said        B o o b ies….. haha.   Yeah, no… grilling is on hiatus for a bit.
    • Chicken mine,  melded in Mccormick poultry seasoning for 24 hours.  Grill will get a break till the frigid temps go away!
    • we had some nice weather yesterday and this conundrum was driving me crazy  so I drove up to the house to take another look. I got a bunch of goodies via ups yesterday (cables,  winch ratchet parts, handles, leaf springs etc).   I wanted to make sure the new leaf springs I got fit. I got everything laid out and ready to go. Will be busy this weekend with kids stuff and too cold to fish anyway, but I will try to get back up there again next weekend and get it done. I don't think it will be bad once I get it lifted up.    For anyone in the google verse, the leaf springs are 4 leafs and measure 25 1/4" eye  to eye per Yetti. I didnt want to pay their markup so just got something else comparable rated for the same weight.   I am a first time wheel house owner, this is all new to me. My house didn't come with any handles for the rear cables? I was told this week by someone in the industry that cordless drills do not have enough brake to lower it slow enough and it can damage the cables and the ratchets in the winches.  I put on a handle last night and it is 100% better than using a drill, unfortatenly I found out the hard way lol and will only use the ICNutz to raise the house now.
  • Topics

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.