Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. ?

  • 0

John Deere Engine Problems


hooksetter

Question

I have a little JD riding mower with an 8 hp rear engine. It starts fine and runs fine until a certain point - when it gets warmed up/hot - at which point it stops and won't run again until it cools down. I have checked the fuel line, the carb, and I don't know what to do next.

Any ideas?

Thanks for the help!

Link to comment
Share on other sites

8 answers to this question

Recommended Posts

  • 0

I have a smaller (6.5) horsepower push mower that does the exact same thing. If it is possible, slow the rpms down before shutting it off, and then "feather" the shut down. I do it with the safety bar on the mower, you maybe could use the seat safety switch? What I mean by feather, is let it almost die and bring it back just enough to not let it die completly. Do this a few times, finnally let it die. If it starts shortly after, it is a fuel problem. The motor is choking itself out. When you feather it off, it uses enough of the fuel in the carb so it will start again. If you shut it off at WOT it fills the carb with fuel and it will never start, well it will if you pull it (I don't have electric start) about 100 times. When the motor has time to cool down, the fuel in the carb has time to evaporate. My neigbors JD mower does the same thing. Is it a briggs and straton INTEK?

Good Luck

Link to comment
Share on other sites

  • 0

I have a B & S 18 hp intek on my mower that does similar problem sometimes. If I park it after mowing with over 1/3 tank of gas, apparantly the needle and seat/carb float stick or hang partially open because it will really flood - even filling the cylinder with gas (it only does this about 1 out of 3 times). To restart mine I have to pull the spark plugs, spin it over with them out to get rid of the excess gas, replace them, then it will restart. I try to always finish with the tank low - then no problems.

Link to comment
Share on other sites

  • 0

Quote:

I have a little JD riding mower with an 8 hp rear engine. It starts fine and runs fine until a certain point - when it gets warmed up/hot - at which point it stops and won't run again until it cools down. I have checked the fuel line, the carb, and I don't know what to do next.

Any ideas?

Thanks for the help!


You get it figured out let me know. I bet it is a Model 68 grin.gif. I have the same one and same problem. I have given up on trying to figure it out and know it sits in the coner of the garage and collects dust.

Link to comment
Share on other sites

  • 0

I think I have it figured out! By Accident!!

I was wiggling all of the wire connections and one broke off in my hand. I put a new end on it and tightened it back down and magically it has run great since.

I haven't dug deep enough to know where it goes to but it is a wire on the carburator side slightly to the rear of the carb that goes up underneath toward the coil? maybe?

Thanks for the good tips on the thought that maybe it was electrical. In fact I had ordered a new ignition and coil but now I don't need it. I can try to post a picture of the wire if anyone is interested. grin.gif

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.


  • Your Responses - Share & Have Fun :)

    • Sorry to hear that Duff. Will give my GSP's an extra scratch behind the ear for you guys today
    • Aw, man, sorry to hear that.  Shed some tears and remember her well.  They all take a piece of our hearts with them; some more than others.
    • yes sorry for your loss..  our dogs are always special...
    • Truly sorry to hear that duffman! I know that feeling.  Keep the good memories  
    • Chamois passed away this weekend a couple days short of her 13th bday. What a great dog to hang out with here at home and on distant adventures. Gonna miss ya big time my little big girl.
    • Sounds pretty sweet, alright. I will check them out, thanks.
    • If you really want to treat your wife (and yourself) with a remote operated trolling motor, the Minn Kota Ulterra is about easy as it gets.  Auto stow and deploy is pretty awesome.  You just have to turn the motor on when you go out and that the last time you have to touch it.   24V 80lb.  60 inch shaft is probably the right length for your boat.  They ain’t cheap - about $3k - but neither one of you would have to leave your seat to use it all day.
    • Wanderer, thanks for your reply. I do intend for it to be 24 volt, with a thrust of 70-80. Spot lock is a must (my wife is looking forward to not being the anchor person any more).  With my old boat we did quite a lot of pulling shad raps and hot n tots, using the trolling motor. Unlikely that we will fish in whitecaps, did plenty of that when I was younger. I also need a wireless remote, not going back to a foot pedal. We do a fair amount of bobber fishing. I don't think I will bother with a depth finder on the trolling motor. I am leaning toward moving my Garmin depth finder from my old boat to the new one, just because I am so used to it and it works well for me. I am 70 years old and kinda set in my ways...
    • Dang, new content and now answers.   First, congrats on the new boat!   My recommendation is to get the most thrust you can in 24V, assuming a boat that size isn’t running 36V.  80 might be tops?  I’m partial to MinnKota.     How do you plan to use the trolling motor is an important question too.     All weather or just nice weather?   Casting a lot or bait dragging?   Bobber or panfish fishing?   Spot lock?  Networked with depth finders?  What brand of depth finders?
  • Topics

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.