Jump to content

  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. ?

strikemaster not starting.

korupt21

By korupt21
in Ice Fishing

 Share

Recommended Posts

korupt21 Contributor

korupt21

Posted
Posted

I have an older strickmaster. When I pull the starter cord the engine will not turn over and run. However, I sprayed some starter fluid into the carborator ( I think ), through the hole where the spark plug is inserted, and pulled the cord. The engine will start and run for a second or so and quit. So basically the starter fluid is burning to fire up the engine and then once burnt the engine will not fire. assume the spark plug is good or the starter fluid would not ignite, correct. I believe it's new.

Being mechanically retarded, I have no idea what I need to repair or what would be causing this issue. Does anybody have any suggestions for me?

Link to comment
Share on other sites
Guest

Guest

Posted
Posted

#1 .. dont spray any more starting fluid in there... its a good way to cause serious damage.

Your carb is gummed up somewhere. If you have a friend that tinkers with engines at all, they should be able to clean it out, or put a rebuild kit in it.

If your in the metro and dont know anyone, I can help you out. Otherwise any small engine shop will be able to service it. It usually can be taken care of in about an hour(once they get to it), sometimes the parts have to sit in carb cleaner overnight.

Link to comment
Share on other sites
Surface Tension Grand Master

Surface Tension

Posted
Posted

The spark plug hole is on the head and the head is bolted onto the cylinder. The gas tank has a fuel line that goes to

the carb. If that line is good(no cracks) then make sure your using the choke, its the lever attached to the carb. It should be closed when starting a cold engine. If that doesn't do the trick you should bring it in.

Link to comment
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Your Responses - Share & Have Fun :)

    • Mike89
      Problems with Yetti

      By Mike89 · Posted

      good luck!!!   
    • rundrave
      Problems with Yetti

      By rundrave · Posted

      we had some nice weather yesterday and this conundrum was driving me crazy  so I drove up to the house to take another look. I got a bunch of goodies via ups yesterday (cables,  winch ratchet parts, handles, leaf springs etc).   I wanted to make sure the new leaf springs I got fit. I got everything laid out and ready to go. Will be busy this weekend with kids stuff and too cold to fish anyway, but I will try to get back up there again next weekend and get it done. I don't think it will be bad once I get it lifted up.    For anyone in the google verse, the leaf springs are 4 leafs and measure 25 1/4" eye  to eye per Yetti. I didnt want to pay their markup so just got something else comparable rated for the same weight.   I am a first time wheel house owner, this is all new to me. My house didn't come with any handles for the rear cables? I was told this week by someone in the industry that cordless drills do not have enough brake to lower it slow enough and it can damage the cables and the ratchets in the winches.  I put on a handle last night and it is 100% better than using a drill, unfortatenly I found out the hard way lol and will only use the ICNutz to raise the house now.
    • Wanderer
      Problems with Yetti

      By Wanderer · Posted

      I haven’t done any leaf springs for a long time and I can’t completely see the connections in your pics BUT I I’d be rounding up: PB Blaster, torch, 3 lb hammer, chisel, cut off tool, breaker bar, Jack stands or blocks.   This kind of stuff usually isn’t the easiest.   I would think you would be able to get at what you need by keeping the house up with Jack stands and getting the pressure off that suspension, then attack the hardware.  But again, I don’t feel like I can see everything going on there.
    • rundrave
      Problems with Yetti

      By rundrave · Posted

      reviving an old thread due to running into the same issue with the same year of house. not expecting anything from yetti and I already have replacement parts ordered and on the way.   I am looking for some input or feedback on how to replace the leaf springs themselves.    If I jack the house up and remove the tire, is it possible to pivot the axel assembly low enough to get to the other end of the leaf spring and remove that one bolt?   Or do I have to remove the entire pivot arm to get to it? Then I also have to factor in brake wire as well then. What a mess   My house is currently an hour away from my home at a relatives, going to go back up and look it over again and try to figure out a game plan.           Above pic is with house lowered on ice, the other end of that leaf is what I need to get to.   above pic is side that middle bolt broke and bottom 2 leafs fell out here is other side that didnt break but you can see bottom half of leaf already did but atleast bolt is still in there here is hub assembly in my garage with house lowered and tires off when I put new tires on it a couple months ago. hopefully I can raise house high enough that it can drop down far enough and not snap brake cable there so I can get to that other end of the leaf spring.
    • smurfy
      Just Food and Drink

      By smurfy · Posted

      Chef boyardee pizza from the box!
    • smurfy
      Just Food and Drink

      By smurfy · Posted

      Enchiladas 
    • smurfy
      Just Food and Drink

      By smurfy · Posted

      Venny neck roast!
    • Wanderer
      Merry Christmas

      By Wanderer · Posted

      Or he could go with leech~~~~~
    • Big Dave2
      Merry Christmas

      By Big Dave2 · Posted

      Bear can relate too. Tell Leech to start a new account named Leech5, we'll know who he is.If he has any trouble, Bear can walk him through it.
    • hugonian1
      Merry Christmas

      By hugonian1 · Posted

      Blessed Christmas to all.  

  • Topics

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.

  I accept