Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. ?

Heaters for Wheelhouses


vman11

Recommended Posts

I have a Remington REM10PT wall heater, 10,000 BTU (bought at Menards), and it will not light anymore. I put a new regulator on it and cleaned the pilot with still no luck. It has gotten progressively worse and worse and it actually acted up the first time it was used. Has anybody else had a problem? I am going to return it - it is still under warranty.

Any recommendations for other heaters? If so, how much did they cost and where can you find them?

Link to comment
Share on other sites

I had a Remington that I purchased at Menards also. I had problems with the thermostat not opening and closing. The flame would die off real slow. I tried everything from the regulator to the hose. I found a replacement reg for it, but it cost more than purchasing a new heater. I would return yours for a new one. I did purchase a new one, and never had any problems after that. They are a good heater for the money. The only thing that I didn't like about that style of heater was all the moisture it gave off. I will be putting in a forced air in my next one.

Link to comment
Share on other sites

Same problems here. My Remington still works but it's always something on it that isn't right. When I push in the knob to light it, it gets stuck down. My regulator has always gave me fits. The flame always goes down as it runs. The settings on the knob are worthless because mine has the same flame on setting 1 as it does on the highest, has to be lower than one to actually make the flame go down.

If I had it to do over, and I might for next year, I'd put in a regular stove type that sits by the floor. Nu-way I believe is the brand.

Link to comment
Share on other sites

we have a kerosine heater in the garage dont see why that would work you can buy them at most fleet stores. its buyin the gas that sometimes can be a pain luckily we have a bp that sells it out of the pump and I know some FF have it in pump from also. very effective way to heat the garage would not see why it would be ne different in a wheelhouse.. being able to take when you leave is a plus too..

Link to comment
Share on other sites

we have a kerosine heater in the garage dont see why that would work you can buy them at most fleet stores. its buyin the gas that sometimes can be a pain luckily we have a bp that sells it out of the pump and I know some FF have it in pump from also. very effective way to heat the garage would not see why it would be ne different in a wheelhouse.. being able to take when you leave is a plus too..

I was thinking of doing the same thing. Ah, the smell of burning kerosine brings back good memories with the Grandfather in his shed doing woodburning projects as a kid. The good old days.

Link to comment
Share on other sites

Originally Posted By: dan z
we have a kerosine heater in the garage dont see why that would work you can buy them at most fleet stores. its buyin the gas that sometimes can be a pain luckily we have a bp that sells it out of the pump and I know some FF have it in pump from also. very effective way to heat the garage would not see why it would be ne different in a wheelhouse.. being able to take when you leave is a plus too..

I was thinking of doing the same thing. Ah, the smell of burning kerosine brings back good memories with the Grandfather in his shed doing woodburning projects as a kid. The good old days.

I have a wood stove in mine...

When you measure out the price compared to propane... The wood stove paid for itself in the first winter... Now I just cut a half cord of oak each spring, let it dry and we're all good to go in the winter... Free heating... Never freezes up... Don't get all that over humid air steaming up the place. (Though we do simmer water into the air.)

And since wood is already part of the natural cycle (It's going up into the atmosphere if it rots on the forest floor or if I burn it.) I'm also heating my fish house "Carbon Neutral."

Link to comment
Share on other sites

Quote:

Looking at the measurements of that stove, it looks to be very compact. Do you know if they have a blower that could be mounted to it to direct the heat through duct work?

I don't think they do. You might have to engineer that part yourself.

I like the compact size too, thinking about trying that kind for next year.

Link to comment
Share on other sites

Unless it's a direct vent heater that exhausts to the outside and also draws air in from outside to use in the cumbustion chamber, they are not recommended for sleeping. The direct vents only burn oxygen they draw in from outside the house, not the oxygen inside the house.

I have seen where people drill a hole in the side of the house and have a small piece of PVC pipe come inside under the stove. This will draw air in from outside.

I personally would be hesitant to sleep in a house that does not have a direct vent heater.

I have an old Nuway kerosene burner in one of my houses. It works great and there's just something cool about the smoke billowing out the chimney. Although, the kerosene isn't as convenient as the propane.

Link to comment
Share on other sites

Join the conversation

You can post now ↓↓↓ or ask your question and then register. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Your Responses - Share & Have Fun :)

    • got this tackled today took about 3 hours to get both sides done. Didnt even get to use a torch....   Thought I was golden with just jacking it up and I could get to everything but no luck. Had to remove the entire axle hub and brake assembly to get to what I needed. Was a pain but still better then taking off the entire pivot arm.    Axle bearings were already greased and in great shape thankfully. Got both leaf springs installed and its ready for the road again.   Probably going to have my electric brakes checked, I am not touching anything with the brake drums. Based on what I saw it doesn't look like my electric brakes have been working anyway. Brakes are nice to have if its slippery out
    • By The way that didn't work either!! Screw it I'll just use the cellular. 
    • It’s done automatically.  You might need an actual person to clear that log in stuff up.   Trash your laptop history if you haven’t tried that already.
    • 😂 yea pretty amazing how b o o b i e s gets flagged, but they can't respond or tell me why I  can't get logged in here on my laptop but I can on my cellular  😪
    • I grilled some brats yesterday, maybe next weekend will the next round...  
    • You got word censored cuz you said        B o o b ies….. haha.   Yeah, no… grilling is on hiatus for a bit.
    • Chicken mine,  melded in Mccormick poultry seasoning for 24 hours.  Grill will get a break till the frigid temps go away!
    • we had some nice weather yesterday and this conundrum was driving me crazy  so I drove up to the house to take another look. I got a bunch of goodies via ups yesterday (cables,  winch ratchet parts, handles, leaf springs etc).   I wanted to make sure the new leaf springs I got fit. I got everything laid out and ready to go. Will be busy this weekend with kids stuff and too cold to fish anyway, but I will try to get back up there again next weekend and get it done. I don't think it will be bad once I get it lifted up.    For anyone in the google verse, the leaf springs are 4 leafs and measure 25 1/4" eye  to eye per Yetti. I didnt want to pay their markup so just got something else comparable rated for the same weight.   I am a first time wheel house owner, this is all new to me. My house didn't come with any handles for the rear cables? I was told this week by someone in the industry that cordless drills do not have enough brake to lower it slow enough and it can damage the cables and the ratchets in the winches.  I put on a handle last night and it is 100% better than using a drill, unfortatenly I found out the hard way lol and will only use the ICNutz to raise the house now.
  • Topics

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.