MuleShack Posted May 12, 2013 Share Posted May 12, 2013 I have a Gigabyte G1 Sniper Rev 3 motherboard in my PC that I built last fall. Everything was working great.System Specs:Quote:CPU: Intel Core i7-3770 3.4GHz Quad-Core Processor Motherboard: Gigabyte G1.Sniper 3 EATX LGA1155 Motherboard Memory: Corsair Vengeance 32GB (4 x 8GB) DDR3-1600 Memory Storage: Seagate Constellation ES 1TB 3.5" 7200RPM Internal Hard Drive Storage: Crucial M4 256GB 2.5" Solid State DiskVideo Card: Galaxy GeForce GTX 560 Ti 1GB Video Card Case: Cooler Master HAF 932 Advanced ATX Full Tower Case Optical Drive: Plextor PX-LB950SA Blu-Ray/DVD/CD Writer Monitor: Dell 24.0" Monitor Operating System: Microsoft Windows 7 Professional SP1 (64-bit) So Last Monday I shut everything down, and pulled the plugs because I was painting the office. Got it all put back together on Thursday evening and it worked fine.Then I go to use it on Friday evening and the box is cycling. Wants to fire up and then shuts down after about 2 seconds. Then it waits for about 5-8 seconds then tries to fire up again...same cycle.I tried pulling the power to the motherboard and then hitting the reset button on the motherboard and that didn't cure anything.The MB is flashing error code 15. I sent an email in to the Gigabyte help center but they must only work M-F. So I figured I would cast a line out here to see if anyone has had this issue.Online I keep coming up with BIOS updates, but that doesn't do me any good if I cant get the PC up and running first.I'm going to try to remove the video card next and see if it fires up.Any idea folks? Quote Link to comment Share on other sites More sharing options...
upnorth Posted May 13, 2013 Share Posted May 13, 2013 Unplug everything short of the monitor and see what you get. Might even try the ram too. Quote Link to comment Share on other sites More sharing options...
MuleShack Posted May 13, 2013 Author Share Posted May 13, 2013 I unplugged the monitor.I tried to use 2 sticks of ram instead of 4 and rotated them, then it started constantly beeping and flashed error 53. Even after I put all 4 back in.I have also taken out the video card but nothing has changed.in the manual, it says constant short beeps are power supply issue. but cant find what error code 53 is. Quote Link to comment Share on other sites More sharing options...
upnorth Posted May 13, 2013 Share Posted May 13, 2013 Unless they have online listed for the error codes and you will need to contact the vendor to find out the codes mean. Quote Link to comment Share on other sites More sharing options...
LMITOUT Posted May 13, 2013 Share Posted May 13, 2013 The manual I found online says that error code 50-55 results when a "memory initialization error occurs".Error code 15: "Pre-memory North-Bridge initialization is started". Quote Link to comment Share on other sites More sharing options...
Shack Posted May 13, 2013 Share Posted May 13, 2013 Scouted around some sites and found this to try:Quote:I have the same problem. I fixed it by taking everything out [i.E ram, gpu, sound(if you have one), any usb devices, and the cmos battery] (leave your CPU seated with cooling of course. Then you would use a jumper by the BIOS switch located on the bottom middle of the MOBO and leave it for a good half hour unplugged if you have the patience to wait a day I'm sure it'll work as well. After you have waited, take jumper out and place CMOS battery back in and try to start it without GPU and RAM to purposely trip a error to see if your MOBO is working correctly. If you hear a beeping from the MOBO speaker then you should be good. Reseat everything and start it up, it should be good. Hope this helpsProper clearing CMOS and leaving it sit for over 10 minutes with no battery or power would be my first attempt. Short of that I found others who ended up getting a refund or replacement motherboard in the end. Quote Link to comment Share on other sites More sharing options...
MuleShack Posted May 13, 2013 Author Share Posted May 13, 2013 Thanks,I just pulled everything and letting it sit while at work today and will try tonight and see what happens. Quote Link to comment Share on other sites More sharing options...
MuleShack Posted May 13, 2013 Author Share Posted May 13, 2013 The manual I found online says that error code 50-55 results when a "memory initialization error occurs".Error code 15: "Pre-memory North-Bridge initialization is started". Do you have the link in your browser history yet? I found a 128 page pdf manual but didn't see any thing about error codes listed. Maybe I missed it. Quote Link to comment Share on other sites More sharing options...
LMITOUT Posted May 13, 2013 Share Posted May 13, 2013 The one I downloaded is 128 pages too. The title is "G1.Sniper 3" Rev. 1003.The debug codes start on page 118 in the appendix. Quote Link to comment Share on other sites More sharing options...
MuleShack Posted May 13, 2013 Author Share Posted May 13, 2013 Turns out ya have to hold down the CMOS reset button for 5-10 seconds. I thought you just had to push it in. Got it back up and running with 1 stick of ram, then added the 2nd and all was still good. Then went back out to add the other 2 sticks and then it errored out again. So I have a bad stick of RAM or slots 2 & 4 are bad on the mother board. Quote Link to comment Share on other sites More sharing options...
Shack Posted May 13, 2013 Share Posted May 13, 2013 You could fire it up with the suspect sticks of RAM in the known good slots and see what happens. Taking out the cmos battery for more than 10 to 20 minutes to clear it should trump any reset jumpers, buttons or procedures. Quote Link to comment Share on other sites More sharing options...
delcecchi Posted May 14, 2013 Share Posted May 14, 2013 Do they still use some sort of battery CMOS instead of NVRAM (flash) to hold configuration information? Boggles the mind. Quote Link to comment Share on other sites More sharing options...
MuleShack Posted May 14, 2013 Author Share Posted May 14, 2013 You could fire it up with the suspect sticks of RAM in the known good slots and see what happens. Taking out the cmos battery for more than 10 to 20 minutes to clear it should trump any reset jumpers, buttons or procedures. I took it apart again and subbed out the number 1 slot ram with the 2 remaining pieces. It failed with each of them in the number one slot. So it would seem that I killed two DDR3 memory chips some how? Good thing I got 4 to begin with. Quote Link to comment Share on other sites More sharing options...
upnorth Posted May 14, 2013 Share Posted May 14, 2013 The electronics in PCs are like light bulbs, stuff goes without warning or apparent reason. Quote Link to comment Share on other sites More sharing options...
Shack Posted May 14, 2013 Share Posted May 14, 2013 The electronics in PCs are like light bulbs, stuff goes without warning or apparent reason. +1 and especially regarding DDR3 memory. There is a reason why you can buy a Gig of DDR3 at the fraction of the price of DDR2 or older versions of DIMM. Quote Link to comment Share on other sites More sharing options...
bobbymalone Posted May 14, 2013 Share Posted May 14, 2013 I took it apart again and subbed out the number 1 slot ram with the 2 remaining pieces.It failed with each of them in the number one slot.So it would seem that I killed two DDR3 memory chips some how?Good thing I got 4 to begin with. I thought those RAM slots were paired... Meaning if one chip or one slot goes bad the pair goes bad... Quote Link to comment Share on other sites More sharing options...
MuleShack Posted May 14, 2013 Author Share Posted May 14, 2013 Not an expert by any means, just a DIY'r. I did hear that they have to be in pairs, because the slots on the MB are color coded Green on 1 & 3 and Black on 2 & 4. I didn't realize that they go bad in pairs though...but I guess it would make sense. Now i'm going to see if they have a warranty on them? Quote Link to comment Share on other sites More sharing options...
delcecchi Posted May 14, 2013 Share Posted May 14, 2013 +1 and especially regarding DDR3 memory. There is a reason why you can buy a Gig of DDR3 at the fraction of the price of DDR2 or older versions of DIMM. Goes to show you should not pet the cat while working on your motherboard. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now ↓↓↓ or ask your question and then register. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.