Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. ?

  • 0

Checklist Needed For Winterizing a Merc Four Stroke


Juan Grande

Question

I'm winterizing my boat for the first time and was wondering if someone could give me a checklist of what I need to do?

I have a Merc 115 four stroke outboard. What do I need to do as far as fogging, changing the oil, etc.

I'm also wondering what I need to do on the boat itself? Do I need to pull the batteries, flush the livewell lines, bilge, etc.? I'm storing the boat outside so do I need to fill the lines with anti-freeze or just blow them out?

Any help would be greatly appreciated.

John

Link to comment
Share on other sites

2 answers to this question

Recommended Posts

  • 0

With motor hooked to muffs or a water supply disconnect gas while running motor and when it starts to race spray fogging oil into the carb. Keep doing it for about a minute then really spray hard till it dies. Most motors will die immediatly with the fogging oil some motors will run forever on it. Remove plugs and spray each cylinder real good then replace the plugs and give it a quick crank with plug wires disconnected.

Drain and fill lower unit oil, Pull plug on boat and tilt back so any water getting in will drain. Jack trailer up and use jack stands to reduce flat spots on tire treads. I am sure there is others but the most important is draining and re filling the lower unit. If there is water in there and it freezes it can bust open that lower unit.

Link to comment
Share on other sites

  • 0

Quote:

when it starts to race spray fogging oil into the carb.


I'm not 100% certain, but I believe the 115 Merc 4 Stroke is fuel injected.. which means there are no carbs to spray the fogging fluid into. What I would do is to run a fuel stabalizer (stabil, seafoam, 2+4, etc) and run the engine for a while on the hose to make sure you've got stabalized fuel run through the fuel system on the motor. Then, remove the spark plugs, squirt some fogging fluid into the cylinders and then, with the spark plug wires off or with the kill switch pulled, turn the engine over a little bit to get the fluid worked in.

Everything else is correct above.

marine_man

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.


  • Your Responses - Share & Have Fun :)

    • we had some nice weather yesterday and this conundrum was driving me crazy  so I drove up to the house to take another look. I got a bunch of goodies via ups yesterday (cables,  winch ratchet parts, handles, leaf springs etc).   I wanted to make sure the new leaf springs I got fit. I got everything laid out and ready to go. Will be busy this weekend with kids stuff and too cold to fish anyway, but I will try to get back up there again next weekend and get it done. I don't think it will be bad once I get it lifted up.    For anyone in the google verse, the leaf springs are 4 leafs and measure 25 1/4" eye  to eye per Yetti. I didnt want to pay their markup so just got something else comparable rated for the same weight.   I am a first time wheel house owner, this is all new to me. My house didn't come with any handles for the rear cables? I was told this week by someone in the industry that cordless drills do not have enough brake to lower it slow enough and it can damage the cables and the ratchets in the winches.  I put on a handle last night and it is 100% better than using a drill, unfortatenly I found out the hard way lol and will only use the ICNutz to raise the house now.
    • I haven’t done any leaf springs for a long time and I can’t completely see the connections in your pics BUT I I’d be rounding up: PB Blaster, torch, 3 lb hammer, chisel, cut off tool, breaker bar, Jack stands or blocks.   This kind of stuff usually isn’t the easiest.   I would think you would be able to get at what you need by keeping the house up with Jack stands and getting the pressure off that suspension, then attack the hardware.  But again, I don’t feel like I can see everything going on there.
    • reviving an old thread due to running into the same issue with the same year of house. not expecting anything from yetti and I already have replacement parts ordered and on the way.   I am looking for some input or feedback on how to replace the leaf springs themselves.    If I jack the house up and remove the tire, is it possible to pivot the axel assembly low enough to get to the other end of the leaf spring and remove that one bolt?   Or do I have to remove the entire pivot arm to get to it? Then I also have to factor in brake wire as well then. What a mess   My house is currently an hour away from my home at a relatives, going to go back up and look it over again and try to figure out a game plan.           Above pic is with house lowered on ice, the other end of that leaf is what I need to get to.   above pic is side that middle bolt broke and bottom 2 leafs fell out here is other side that didnt break but you can see bottom half of leaf already did but atleast bolt is still in there here is hub assembly in my garage with house lowered and tires off when I put new tires on it a couple months ago. hopefully I can raise house high enough that it can drop down far enough and not snap brake cable there so I can get to that other end of the leaf spring.
    • Chef boyardee pizza from the box!
    • Or he could go with leech~~~~~
    • Bear can relate too. Tell Leech to start a new account named Leech5, we'll know who he is.If he has any trouble, Bear can walk him through it.
    • Blessed Christmas to all.  
  • Topics

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.