Jump to content

  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. ?

Mower won't stay running

ishy

By ishy
in Lawn & Garden

 Share

Recommended Posts

ishy Enthusiast

ishy

Posted
Posted

Craftsman push mower. Pump the primer bulb, starts and then stops. Fuel line was cracked< so I thought I was sucking in air. Replaced that, same thing. Fresh gas, added a little sea Faom to gas and oil crancase. Nothing. Sprayed carb cleaner in. If I keep pumping the primer bulb it will stay running and I can see the carb flap open and close as the engine revs. Thank you..

Link to comment
Share on other sites
leech~~ Grand Master

leech~~

Posted
Posted

Check the little stupid safety handle cable that wouldn't let you run the mower without holding it. I have had two of them where the cable would be so tight that it would shut off. I had to disconnect them and hold the switch open with a screw driver to get it to run. wink

Link to comment
Share on other sites
ishy Enthusiast

ishy

Posted
  • Author
Posted

Air filter clean. Will check the jet on the carb and the cable and do the Google search. Thanks to all. I will let you know what the problem was once it's fixed..

Link to comment
Share on other sites
fishersofmen Grand Master

fishersofmen

Posted
Posted

Definitely sounds like the carb. If it will run when pumping the primer its not getting enough gas which is usually the problem. There have been times where I can just drop the bowl or drain plug off the bottom of a carb and let the gunk drain out and a motor will run fine and other times I need to take everything apart and spray it down....

Link to comment
Share on other sites
ishy Enthusiast

ishy

Posted
  • Author
Posted

Pulled the main jet and the bowl off. Used the bread tag wire and cleaned the jet and the little hole on the face of the carb. Started on the second pull. Not bad for 14 years old. Thanks to all. You guys rock.

Link to comment
Share on other sites

Join the conversation

You can post now ↓↓↓ or ask your question and then register. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Your Responses - Share & Have Fun :)

    • Wanderer
      New boat question

      By Wanderer · Posted

      As a recovering machinist, I can appreciate that.  If the spec is 0.001 - 0.0015, then clearly the correct measurement is 0.00125, duh…
    • Crow Hunter
      New boat question

      By Crow Hunter · Posted

      I just figured that it is easy enough to just get a 3 bank so when the boat is not in use I can keep all 3 batteries charged. I have not bough a charger yet, maybe I will give it some more thought. Edit: After thinking this over, with the size, weight, and heat output of the charger (as well as the cost) I think it makes sense to just buy a 2 bank charger, I have a smaller charger i can use on the starting battery when the boat is sitting at home. Forgive me, for i am a retired engineer and I have to obsess over everything...
    • Wanderer
      New boat question

      By Wanderer · Posted

      Congrats on the motor!  I think you’ll like it.   I can’t say much on the charger location but I’ve seen them under the lid in back compartments and under center rod lockers.  160 degrees is more than I expected to hear.   Curious why you’re opting for a 3 bank charger with a 24V trolling motor.  Unless you don’t feel you be running you big motor enough to keep that battery up as well?
    • Crow Hunter
      New boat question

      By Crow Hunter · Posted

      I did buy an Minnkota Ulterra, thanks for the recommendations. I had a bunch of Cabela"s bucks saved up, which helped. Now i need to get an onboard battery charger. Where do you guys mount these things in your boat? The manufacturer I am looking at {Noco genius) says tht their 3-bank charger will run at 160 degrees, seems like a lot of heat in an enclosed compartment? Thanks for any input on this.
    • Duffman
      Random Daily Pics

      By Duffman · Posted

      You're very lucky a troop of Sea Monkey's didn't carry you away.   
    • bobbymalone
      Random Daily Pics

      By bobbymalone · Posted

      Wasn't terrible at a state park beach. Antelope island maybe.  I wouldn't recommend it as a beach destination tho.  Figured I was there, I'm getting in it.
    • SledNeck
      Random Daily Pics

      By SledNeck · Posted

      The water looked and smelled disgusting with hundreds of thousands of birds sh*tting in there.  About as gross as the Salton Sea. When I duck hunted there I didn't even want to touch the water.
    • bobbymalone
      Random Daily Pics

      By bobbymalone · Posted

      It's kinda gross with the algae in the summer but I got in it anyway.  Wanted to see the increased bouyancy at work.  You can kinda tuck yourself into a ball and you'll just float with your head above water.  When dry off you look diamond encrusted with the salt.
    • Macgyver55
      Random Daily Pics

      By Macgyver55 · Posted

      We went to the flats too. I dipped a tire on the rental car onto it just to say I’ve been there,but it was still pretty soft from winter melt. After seeing some moron in a BMW suv get dragged out of the muck I had no intention of repeating his stupidity. 
    • SledNeck
      Random Daily Pics

      By SledNeck · Posted

      I've been out on the flats. It's like being on a different planet 

  • Topics

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.

  I accept