Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. ?

Snap Swivels


Jordpederson

Recommended Posts

Depends on the lure. Usually with crankbaits of medium or large size using a snap swivel is fine. Spinners and spinnerbaits are fine too. A lot of jerkbaits work well. It's the other lures and small lures that often lose action. As exception is certain popper frogs. a swivel will pull the nose down some and make them have a louder pop and some even will walk the dog a bit. But cheap popper frogs tend to just sink with one on.

Link to comment
Share on other sites

This is not scientific by any means, but when fishing crank baits of the same color, line, rod, etc... I have found the the lure that was attached with a ball bearing swivel caught more fish than the same lure directly tied to the lure.

I'm not sure, but in some cases a swivel may increase the action of the lure. Even if it was a very subtle difference.

We noticed that was the only difference when one was catching and one wasn't. We were trolling the lures at the time and they were #5 shad raps.

I have found that on some lures that they actually due effect the motion of the lure for me, Flicker shads for one, don't run for me as true with a swivel as they do direct tied to the line. Just one Man's observation.

Mike

Link to comment
Share on other sites

I like them and enjoy using them. Havent noticed any change, although I have heard about it. I also use a flouroleader or sometimes a steel leader. But the snaps help with time so no knots.

Link to comment
Share on other sites

I tend to believe snap swivels, especially the larger ones, reduce the lure action. I've seen this time and time again with all other things being equal. Direct tieing is great, but who has time for that?

I like to use the smallest Duolock snaps (no swivel) and remove the split rings from the lures. I think I get more action this way and it's less visible as well. The only lures where I will not remove the split ring are lures like a Deep Husky Jerk or Jointed Shad Rap where the connection point is set lower than the bill.

I will use swivel snaps with spoons as they get all twisted up with just the snap.

Link to comment
Share on other sites

Join the conversation

You can post now ↓↓↓ or ask your question and then register. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Your Responses - Share & Have Fun :)

    • By The way that didn't work either!! Screw it I'll just use the cellular. 
    • It’s done automatically.  You might need an actual person to clear that log in stuff up.   Trash your laptop history if you haven’t tried that already.
    • 😂 yea pretty amazing how b o o b i e s gets flagged, but they can't respond or tell me why I  can't get logged in here on my laptop but I can on my cellular  😪
    • I grilled some brats yesterday, maybe next weekend will the next round...  
    • You got word censored cuz you said        B o o b ies….. haha.   Yeah, no… grilling is on hiatus for a bit.
    • Chicken mine,  melded in Mccormick poultry seasoning for 24 hours.  Grill will get a break till the frigid temps go away!
    • we had some nice weather yesterday and this conundrum was driving me crazy  so I drove up to the house to take another look. I got a bunch of goodies via ups yesterday (cables,  winch ratchet parts, handles, leaf springs etc).   I wanted to make sure the new leaf springs I got fit. I got everything laid out and ready to go. Will be busy this weekend with kids stuff and too cold to fish anyway, but I will try to get back up there again next weekend and get it done. I don't think it will be bad once I get it lifted up.    For anyone in the google verse, the leaf springs are 4 leafs and measure 25 1/4" eye  to eye per Yetti. I didnt want to pay their markup so just got something else comparable rated for the same weight.   I am a first time wheel house owner, this is all new to me. My house didn't come with any handles for the rear cables? I was told this week by someone in the industry that cordless drills do not have enough brake to lower it slow enough and it can damage the cables and the ratchets in the winches.  I put on a handle last night and it is 100% better than using a drill, unfortatenly I found out the hard way lol and will only use the ICNutz to raise the house now.
    • I haven’t done any leaf springs for a long time and I can’t completely see the connections in your pics BUT I I’d be rounding up: PB Blaster, torch, 3 lb hammer, chisel, cut off tool, breaker bar, Jack stands or blocks.   This kind of stuff usually isn’t the easiest.   I would think you would be able to get at what you need by keeping the house up with Jack stands and getting the pressure off that suspension, then attack the hardware.  But again, I don’t feel like I can see everything going on there.
    • reviving an old thread due to running into the same issue with the same year of house. not expecting anything from yetti and I already have replacement parts ordered and on the way.   I am looking for some input or feedback on how to replace the leaf springs themselves.    If I jack the house up and remove the tire, is it possible to pivot the axel assembly low enough to get to the other end of the leaf spring and remove that one bolt?   Or do I have to remove the entire pivot arm to get to it? Then I also have to factor in brake wire as well then. What a mess   My house is currently an hour away from my home at a relatives, going to go back up and look it over again and try to figure out a game plan.           Above pic is with house lowered on ice, the other end of that leaf is what I need to get to.   above pic is side that middle bolt broke and bottom 2 leafs fell out here is other side that didnt break but you can see bottom half of leaf already did but atleast bolt is still in there here is hub assembly in my garage with house lowered and tires off when I put new tires on it a couple months ago. hopefully I can raise house high enough that it can drop down far enough and not snap brake cable there so I can get to that other end of the leaf spring.
  • Topics

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.