Guests - If You want access to member only forums on HSO. You will gain access only when you sign-in or Sign-Up on HotSpotOutdoors.

It's easy - LOOK UPPER right menu.

Sign in to follow this  
Followers 0
elbinowalleye

stickers on wood and laquer

7 posts in this topic

I know you can't laquer over stickers on wood, but can you use something else 1st to seal the sticker on the wood and then laquer over it and the rest of the piece of wood? Any advice would be greatly appreaciated. Thanks

Share this post


Link to post
Share on other sites

i used a pour on epoxy. can get it at the M store ,comes in 2 parts..

mix and either pour on or use a fine brush on it.

Share this post


Link to post
Share on other sites

THe clear epoxy would work. I think yoiu could get by with just putting several coats of sanding sealer or varnish over them would work too.

Share this post


Link to post
Share on other sites

I'm interested in the project. What are you doing?

Have you tested for a reaction yet.

Share this post


Link to post
Share on other sites

I used it on a bartop when i built a bar for my neighbor.

He put playing cards and some small fishing flies,photos and some poker chips on it.I used tongue and groove cedar for the bar top,spray adhesive to attach items to the bar,and used the pour on for the final surface. I had to use 2 coats of the pour on to cover everything so surface was smooth.After all was finished,surface is about 1/4 " thick.The bar was finished about 2-3 years ago and no reaction and has held up extremely well.last winter I went over to buff out some scratches and looks like new again. the bar is 36"x96" and took 2 container of the epoxy to do the job( 1 for each coat).thw nice part is it is self leveling so you are guaranteed to have a level surface as long as it is fairly close to begin with.

Share this post


Link to post
Share on other sites

I'm making bean bag boards so would this work for them? I have the stickers on the wood already and hope to find something to seal them on so I can lacquer over the rest of the boards. Can I get this epoxy and just do that and forget about everything else? Thanks for the advice. Never done this before. Learning as I go.

Share this post


Link to post
Share on other sites

the epoxy should work. In taht application I woud use a fine bristle brush to apply it

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  
Followers 0



  • Posts

    • Have a friend that does this....   http://aquaculturenorthamerica.com/Finfish/fresh-water-fish/profitable-commercial-production-for-walleye-and-saugeye/    
    • There's a live rescue going on in Wis Como Lake I think it was right now for a guy that went through but it doesn't look good as they just sent the divers down.   WISN 12 NEWS
    • Ho Ho....   or       Use the fake news thing as a way to censor speech not acceptable to the left.  Yah sure. 
    • Pen raised walleye?   Sounds like fake news.   Lots of Canadian walleye but I think it is netted from wild in places like Lake Winnipeg or Red Lake and so on.   Must be Putin trying to discredit the Canadian Walleye providers. 
    • Quick question. On the striker models they have a setting called the A-scope. It basically widens the right hand part of the screen where it starts so that it works kinda like a showdown at the beginning of the graph which I like on the ice.  Can you check and see if that unit has that?  
    • 5 x 5 will be nor problem for one guy and gear.  I speared out of a two man flip over otter sled for several years and had not problem.  Use to spear out of a 4 x 6 permanent and that is less sq foot than the 5 x 5 hub.  It is nice to have a large hole and yes it lets in more light in those low light conditions but I always used a 3 x 2 spear hole and never had any issues.  It worked, could it be better?  Of course but you just have to figure out what is right for you.  Get a 5 x 5 foot piece of cardboard draw out your hole on it, set up your chair and put all your gear on it and then sit down.  This is probably the closest way to experiencing it prior to doing so...... Good Luck 
    • I've seen walleye at grocery stores in the cities for a buck or two more than king crab.   Yeesh.
    • Well got the unit today first Impressions are I'm really happy with it...I like how the maps included have depth shading...The screen seems very nice...The only thing I don't like so far is the quick release bracket, I feel like I'm going to break it when I pop it off. The transducer is pretty darn huge, not sure if all side imaging ducers are like that or not...Overall very happy for $499, cant wait to get it on the water.
    • Hey you guys!...had to fly into Phoenix couple days ago to check on some golf stuff and while wandering through a big supermarket saw a display of Canadian pen-raised walleye.  It was 18.99 a POUND.   Can you believe that!?  A stinkin'  little 16 ounces of walleye for THAT much money. If a guy could put up with all that sloppy, soft wiggle-wiggle of a battle to boat one a guy could make a pile of money catching them.  Personally,  I'd fall asleep in a walleye hot bite.
  • Our Sponsors