Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. ?

Suggestions getting 8X12 ice house on to trailer?


Moe Szyslak

Recommended Posts

Get one end jacked up with blocking 4 ft back. Use a track jack, you'll find out your blocking will need to be cribbed.

Back your trailer under it. You'll be putting a lot of strain on the trailer till the load is even so use some blocking under the back of the trailer. Remove the blocking under the shack, putting the weight on the trailer. Use a com'along to pull it up the trailer. Once the shack reaches a balance point get some rollers under the skids. Continue to winch into place. Remove rollers for the trip to the lake. Remove the blocking under the trailer. To off load repeat the process in reverse order. The idea here is to use your brain and not your back. Yes its a pain, that is why they invented wheel houses.

Link to comment
Share on other sites

Like the come-along idea, here's another - ATV or truck winch. detach the trailer, pull forward up to the trailer tongue, put a 3/4 inch ply section between you and the hitch as contact surface, and winch up a ramp. This is kinda the same as calling a flatbed wrecker with winch on the bed, but sweat equity and buddies gear instead of Mr. Slick's Towing Co. for a price.

Link to comment
Share on other sites

You could always make more friends! Beer might help! We used to have an 8 x 8 house that we always had to get up on to a trailer to haul to the lake. Always took 5 guys, 4 to lift it and 1 to back the truck up then all 5 to push it the rest of the way on to the trailer.

Is your house on the heavy side or light side for an 8 x 12? That sounds like a lot of weight for a snowmobile trailer. Ours was a heavy beast so we usually used a car trailer.

Link to comment
Share on other sites

Me and 2 buddies just built a 8x12 and we're having the same trouble,we're gunna try come alongs,but we're using a tilt 2 place snowmobile trailer.At first I was thinking it might be to heavy for the trailer,but if you think about what 2 sleds loaded up with snow weigh,thats upward of 1000 pounds...Im not sure what ours weighs,but Id say less than 1500.

Link to comment
Share on other sites

I also back up to a ditch and pull the house straight on. The easiest way I have found to do this is to back the atv into the bed of the truck(and secure it into the bed), run the winch to the fish house and pull the fish house on the trailer with the winch. I also do this when it is time to take the house off of the lake with a trailer that has a ramp gate. This trick works excellent with little to no back strain, but it does require an atv with a good winch.

Link to comment
Share on other sites

jack the house up a few inches and block it up. have the trailer off the truck and tilt the trailer by hand and walk it under the edge of the house. use 2 come-alongs, 1 on either side of the trailer. pull the house up, 2 guys, 1 on either side, at one point the trailer will start to get balanced and the rear of the house will be almost on the trailer. Hook the trailer to the truck. finish winching the house on the trailer, use the come-alongs to secure the house on the way to the lake. Have done it many times, very safe and no damage to the house as everything is moving slow, at first the trailer is pulled under the house. It helps to lube the trailer with a couple shovelsfull of snow.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Your Responses - Share & Have Fun :)

    • Yeah it was a beatdown
    • Your kid needs to stay with him!👍
    • My kid was eating in Beverly Hills and ran into this guy. Talked to him a bit and wished him luck in the game tonight.     
    • 🤔as a recovering machinist!🤣🤣that must make me a recovering welder!
    • As a recovering machinist, I can appreciate that.  If the spec is 0.001 - 0.0015, then clearly the correct measurement is 0.00125, duh…
    • I just figured that it is easy enough to just get a 3 bank so when the boat is not in use I can keep all 3 batteries charged. I have not bough a charger yet, maybe I will give it some more thought. Edit: After thinking this over, with the size, weight, and heat output of the charger (as well as the cost) I think it makes sense to just buy a 2 bank charger, I have a smaller charger i can use on the starting battery when the boat is sitting at home. Forgive me, for i am a retired engineer and I have to obsess over everything...
    • Congrats on the motor!  I think you’ll like it.   I can’t say much on the charger location but I’ve seen them under the lid in back compartments and under center rod lockers.  160 degrees is more than I expected to hear.   Curious why you’re opting for a 3 bank charger with a 24V trolling motor.  Unless you don’t feel you be running you big motor enough to keep that battery up as well?
    • I did buy an Minnkota Ulterra, thanks for the recommendations. I had a bunch of Cabela"s bucks saved up, which helped. Now i need to get an onboard battery charger. Where do you guys mount these things in your boat? The manufacturer I am looking at {Noco genius) says tht their 3-bank charger will run at 160 degrees, seems like a lot of heat in an enclosed compartment? Thanks for any input on this.
    • You're very lucky a troop of Sea Monkey's didn't carry you away.   
    • Wasn't terrible at a state park beach. Antelope island maybe.  I wouldn't recommend it as a beach destination tho.  Figured I was there, I'm getting in it.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.