Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. ?

  • 0

trolling motor question


deadminnowcatcher

Question

I have a 18 ft. lund that has a 24 volt trolling motor on the front. I believe it is 48 lbs of thrust or 55 at the most. It has auto pilot. I no longer fish in tournaments and would rather have a 12 volt trolling motor so i do not need 2 batteries. What 12 volt trolling motor would be comparible???? thinking of selling the 24 volt and buying new 12 volt????

Link to comment
Share on other sites

5 answers to this question

Recommended Posts

  • 0

I hate to contradict you, but fishing tournaments or not, I think you'd be making a big mistake in going to a 12V system with that boat. I think that you may end up finding that on a good day of fishing (especially in any wind) that you'd be hauling along another battery anyway. If the problem is handling the batteries to charge them up, it will probably be less expensive to get an on board charger and then you won't have to take batteries out of the boat.

With that said, you can still look at an autopilot in a comparable lb thrust that will be 12V.

Link to comment
Share on other sites

  • 0

Say with that 18' boat I'm not sure if a 12 volt system would be the way to go. You will lose in thrust power and in battery life. Minn Kota's biggest 12 volt motor is 55#. also bygoing with a 12 volt system your options for shaft length are limited. You still are going to be fishing why not keep fishing with a 24volt system and without having to fight steering. If you down size your boat go with a 12volt.This is just my opinion.

Link to comment
Share on other sites

  • 0

i have had very poor luck with my batteries. I seem to only get a couple years out of them. Not sure if i am doing everything the correct way. If i got an onboard charger would that help??? how often should i then check the water level in them??? and what is the correct level??? Where is a good place to purchase an onboard charger that will install for a reasonable price????

Link to comment
Share on other sites

  • 0

I might be able to answer a couple of your questions.

Would an on-board charger help? Perhaps if you use it. What I mean is, to extend the life of your batteries they should always be recharged as soon as possible. Leaving a battery set with low charge is not good for it, especially if there is a risk of freezing temperatures. The on-board charger is nice because it eliminates the need to hook up every time you want to charge your batteries. All you have to do is plug it in to a 120v outlet.

How often should I check the water level in them? The water level in batteries should be checked regularly. The level should be maintained above the plates. Plates that become exposed are subject to contamination and this is not good. I usually fill mine to the bottom of the tube you see inside. The best is to use distilled water but I have had good luck with the filtered and soft water from my tap.

By the nature of your questions, I also agree that going to 12v is not the answer. As far as increasing running time goes, using 2 batteries in a 12v configuration or 24v will result in very similar overall running time. Going to just one 12v battery will cut your running time in half. This is because the power or watts consumed is the same for the same thrust. The advantage to using 24v systems is that the current draw is less and so you can use smaller wire. If you change from 55# 24v motor circuit to a 55# 12v circuit you may have to replace the supply wires as well.

Hope this helps.

Bob

Link to comment
Share on other sites

  • 0

Quote:

I might be able to answer a couple of your questions.

Would an on-board charger help?
Perhaps if you use it. What I mean is, to extend the life of your batteries they should always be recharged as soon as possible. Leaving a battery set with low charge is not good for it, especially if there is a risk of freezing temperatures. The on-board charger is nice because it eliminates the need to hook up every time you want to charge your batteries. All you have to do is plug it in to a 120v outlet.

Bob


For me, the answer is DEFINITELY to the on-board charger.

My three batteries are 7 years and some odd months old (just checked the date code stickers). The starting battery is a bit weaker now, but still works. The two trolling batteries seem fine.

I'm going to run them until they're un-useable just to see how long they will go. These are not any fancy batteries. The starting battery is an Exide starting/deep cycle and the trolling batteries are Stowaway brand.

My OB charger has an equalization setting that I activate occasionally that is supposed to keep the plates clean and de-sulphated.

Dunno if I'm just lucky, if it's the charger or the equalization, or just good charging practices. I suspect a bit of all. Regardless, something right is going on and that OB charger has long since payed for itself in battery cost and less overall hassles.

BobT is right on the money. In general terms, one 12V battery will last 1/2 as long as two 12V batteries no matter how you hook those two together. Again, that is assuming the motors are of comparable thrust rating and technology.

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.


  • Your Responses - Share & Have Fun :)

    • By The way that didn't work either!! Screw it I'll just use the cellular. 
    • It’s done automatically.  You might need an actual person to clear that log in stuff up.   Trash your laptop history if you haven’t tried that already.
    • 😂 yea pretty amazing how b o o b i e s gets flagged, but they can't respond or tell me why I  can't get logged in here on my laptop but I can on my cellular  😪
    • I grilled some brats yesterday, maybe next weekend will the next round...  
    • You got word censored cuz you said        B o o b ies….. haha.   Yeah, no… grilling is on hiatus for a bit.
    • Chicken mine,  melded in Mccormick poultry seasoning for 24 hours.  Grill will get a break till the frigid temps go away!
    • we had some nice weather yesterday and this conundrum was driving me crazy  so I drove up to the house to take another look. I got a bunch of goodies via ups yesterday (cables,  winch ratchet parts, handles, leaf springs etc).   I wanted to make sure the new leaf springs I got fit. I got everything laid out and ready to go. Will be busy this weekend with kids stuff and too cold to fish anyway, but I will try to get back up there again next weekend and get it done. I don't think it will be bad once I get it lifted up.    For anyone in the google verse, the leaf springs are 4 leafs and measure 25 1/4" eye  to eye per Yetti. I didnt want to pay their markup so just got something else comparable rated for the same weight.   I am a first time wheel house owner, this is all new to me. My house didn't come with any handles for the rear cables? I was told this week by someone in the industry that cordless drills do not have enough brake to lower it slow enough and it can damage the cables and the ratchets in the winches.  I put on a handle last night and it is 100% better than using a drill, unfortatenly I found out the hard way lol and will only use the ICNutz to raise the house now.
    • I haven’t done any leaf springs for a long time and I can’t completely see the connections in your pics BUT I I’d be rounding up: PB Blaster, torch, 3 lb hammer, chisel, cut off tool, breaker bar, Jack stands or blocks.   This kind of stuff usually isn’t the easiest.   I would think you would be able to get at what you need by keeping the house up with Jack stands and getting the pressure off that suspension, then attack the hardware.  But again, I don’t feel like I can see everything going on there.
    • reviving an old thread due to running into the same issue with the same year of house. not expecting anything from yetti and I already have replacement parts ordered and on the way.   I am looking for some input or feedback on how to replace the leaf springs themselves.    If I jack the house up and remove the tire, is it possible to pivot the axel assembly low enough to get to the other end of the leaf spring and remove that one bolt?   Or do I have to remove the entire pivot arm to get to it? Then I also have to factor in brake wire as well then. What a mess   My house is currently an hour away from my home at a relatives, going to go back up and look it over again and try to figure out a game plan.           Above pic is with house lowered on ice, the other end of that leaf is what I need to get to.   above pic is side that middle bolt broke and bottom 2 leafs fell out here is other side that didnt break but you can see bottom half of leaf already did but atleast bolt is still in there here is hub assembly in my garage with house lowered and tires off when I put new tires on it a couple months ago. hopefully I can raise house high enough that it can drop down far enough and not snap brake cable there so I can get to that other end of the leaf spring.
  • Topics

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.