Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. ?

how far off the bottom


hot_bite

Recommended Posts

I have caught walleyes on Little bay de noc 20ft off the bottom fishing in 32ft of water. This is fairly common when fishing a great lakes system. I have seen them on the vex come in near the bottom and have had to work them up, they come up to the lure sniff around but just sit there, then I raise it up a foot or so and they follow it up.This can go on and on until they are only 10ft or so below the ice...then they hit!!! Or sometimes don't hit!! Exciting to say the least!!!Same thing on lake Winnebago here in Wis. Alot of times guys are fishing 16-18ft of water and catching walleyes 5ft below the ice!! The reason those fish are there is because thats where the bait fish are, therefore thats where the hungry walleyes are! I used to fish mainly the bottom 2 feet of water for walleyes and I caught my share, but when I started to fish a little higher and experiment more I caught more fish. Not all fish are right on the bottom, especially the aggressive ones, they are up cruising around looking for something to eat...Those are the ones you should be after, afterall they are easier to catch.

Link to comment
Share on other sites

Rip jigging is haviung the bait on the bottom or the end of the fall and then jigging upward very, very hard and fastwith a long stroke....sometimes as long as 5 feet.

I fish walleyes and sauger thru the winter months from a boat below the Mississippi rive dams. Many fish are taken by concentrating your jigging efforts well off the bottom. In fact, some of the best sauger are taken up to five feet off the bottom when jigging in water 25 feet or more.

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.


  • Your Responses - Share & Have Fun :)

    • we had some nice weather yesterday and this conundrum was driving me crazy  so I drove up to the house to take another look. I got a bunch of goodies via ups yesterday (cables,  winch ratchet parts, handles, leaf springs etc).   I wanted to make sure the new leaf springs I got fit. I got everything laid out and ready to go. Will be busy this weekend with kids stuff and too cold to fish anyway, but I will try to get back up there again next weekend and get it done. I don't think it will be bad once I get it lifted up.    For anyone in the google verse, the leaf springs are 4 leafs and measure 25 1/4" eye  to eye per Yetti. I didnt want to pay their markup so just got something else comparable rated for the same weight.   I am a first time wheel house owner, this is all new to me. My house didn't come with any handles for the rear cables? I was told this week by someone in the industry that cordless drills do not have enough brake to lower it slow enough and it can damage the cables and the ratchets in the winches.  I put on a handle last night and it is 100% better than using a drill, unfortatenly I found out the hard way lol and will only use the ICNutz to raise the house now.
    • I haven’t done any leaf springs for a long time and I can’t completely see the connections in your pics BUT I I’d be rounding up: PB Blaster, torch, 3 lb hammer, chisel, cut off tool, breaker bar, Jack stands or blocks.   This kind of stuff usually isn’t the easiest.   I would think you would be able to get at what you need by keeping the house up with Jack stands and getting the pressure off that suspension, then attack the hardware.  But again, I don’t feel like I can see everything going on there.
    • reviving an old thread due to running into the same issue with the same year of house. not expecting anything from yetti and I already have replacement parts ordered and on the way.   I am looking for some input or feedback on how to replace the leaf springs themselves.    If I jack the house up and remove the tire, is it possible to pivot the axel assembly low enough to get to the other end of the leaf spring and remove that one bolt?   Or do I have to remove the entire pivot arm to get to it? Then I also have to factor in brake wire as well then. What a mess   My house is currently an hour away from my home at a relatives, going to go back up and look it over again and try to figure out a game plan.           Above pic is with house lowered on ice, the other end of that leaf is what I need to get to.   above pic is side that middle bolt broke and bottom 2 leafs fell out here is other side that didnt break but you can see bottom half of leaf already did but atleast bolt is still in there here is hub assembly in my garage with house lowered and tires off when I put new tires on it a couple months ago. hopefully I can raise house high enough that it can drop down far enough and not snap brake cable there so I can get to that other end of the leaf spring.
    • Chef boyardee pizza from the box!
    • Or he could go with leech~~~~~
    • Bear can relate too. Tell Leech to start a new account named Leech5, we'll know who he is.If he has any trouble, Bear can walk him through it.
    • Blessed Christmas to all.  
  • Topics

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.