Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. 😀

  • RECEIVE THE GIFTS MEMBERS SHARE WITH YOU HERE...THEN...CREATE SOMETHING TO ENCHANT OTHERS THAT YOU WANT TO SHARE

    You know what we all love...

    When you enchant people, you fill them with delight and yourself in return. Have Fun!!!

Sign in to follow this  
Lunker

For sale forum?

Recommended Posts

Why can't I post in the for sale forum? How can i register? When I try it gives me the page like I have to become a new user? Any help?

At the Top of the Forum there is a link that says:

How to Post Topic Click Here To Find Out How To Place Your Ad

Click it and follow the directions.

Otherwise, the best way to handle any questions you may have about how the Forum is operating is to use the "Contact Us" link below.

We'll usually see it much sooner.

[This message has been edited by Rick (edited 11-30-2003).]

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  

  • Your Responses - Share & Have Fun :)

    • I always use 6lb mono for jigging rods and And 8lb mono on deadsticks. No leaders for me I’ve debated it but it doesn’t really seem to make a difference if you have one or not. 
    • My thinking is the grease would make up for the gap, but wasn't sure if it'll still have too much play. Yet, don't want it too tight where it gets stuck.
    • I think the tube is DOM 1/2" thick. Was afraid 1/4" too thin and cannot find any other tube that would fit another solid rod inside. Don't want to get something I have to get machined $$$... At least with arm I can pull out and have another made if not good. Not sure how to make the grooves with hand tools?
    • I live in the burbs  on a cul-de-sac and the plow always leaves a huge pile at the end of my driveway. I bought a single stage Toro, and while I don't have a 2-stage to compare it against, I would definitely buy a single stage again. It's plenty powerful enough to handle the deepest, heaviest snow that accumulates on the driveway. When it comes to the pile at the end of the driveway, you just have to work your way though it by backing out and pushing into it again. Of course, if you're out of town or something and the pile at the end of the driveway freezes you might need to get out a shovel. But for most snowfalls I can clean the driveway in a matter of minutes - you almost have to run behind the thing to keep up with it.
    • Not a fan of leaders, far fewer bites with them on.   I typically run 4 or 6 lb test.  I do run 8 lb in water less than 8-10 ft.  I do this because thr fight is usually off to the sides of the hole, and the line contacts the ice edge at sharper angles.    
    • Just ordered the 16 piece jig kit yesterday. I am excited to get them and get out on the ice as soon as it is safe!
    • Hey,   What lb test line should I be using for Walleyes?  I've been using 4 lb but that seems a little light and I don't want to lose the big one, but don't want to get too heavy either.  Also, what's your input on using a leader?  I haven't but just wondering if I am missing something.
    • In my experience the best solution is to have both a single stage and a 2 stage.  The better 2 stage blowers out there will probably be fine for 90% of our snowfalls and in most cases they do a better job on the smaller snowfalls because they scrape the driveway cleaner.  The 2 stages are nice for the really big snowfalls, windblown drifts, and the snowplow drifts.  You can always deal with the lager snow falls by getting out once during the storm to clear the driveway so you don't have so much to do once its all done.    I've had ok luck with a Snapper single stage handling snow plow drifts and smaller wind blown drifts.  You have to go slow and maybe chop up the drift with a shovel if its too big but its doable.  Even if you have to break up the drift a little with a shovel that can be easier than maneuvering a large 2 stage at times.    If I could only have one blower I'd probably opt for one of the larger single stage blowers.  My wife has a hard time handling my large Toro 2 stage and most of the time its just over kill for smaller snowfalls and ends up taking more time than a good single stage would. My mother in law has the Snapper single stage and she can run that just fine on her own so I think almost anyone could. 
    • I would go with DOM (Drawn Over Mandrel). You can find it on-line just a bit pricey unless ypu have a steel supplier nearby that can order it. http://www.aladdinsteel.com/products/dom_seamless_tubing/?gclid=CjwKCAjwwdTbBRAIEiwAYQf_E0tV3qM59rsqxJ1i9ao2mL2_KQ8HhbIdOj_i1FHOUOd9ycq8L9tY0BoCQbIQAvD_BwE#top 1/16, .062 could produce a lot of shift depending on the lenght of your pivot arm. I like .020 max and grove the solid in a level wind criscross pattern for grease distribution. Being steel on steel grease often. During summer also and drop/raise house several times.
    • I think you are good , you need to have room for a ton of grease.
×