Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. ?

  • 0

power steering pump?


arcticcat400

Question

had the power steering pump go out of my 97 chevy z71 so i took it to be replaced after getting it replaced it still wasnt working so i took it back it turns out that the resevoir was leaking so i got it replaced and got it back tonight and on the print out from the shop it said "engine has low rpms so steering is stiff until rpms are raised" so i drove it a while and its very hard to steer from a dead stop but when your moving faster it works fine so my ? is there a way to change the rpms or what do i do?

Link to comment
Share on other sites

6 answers to this question

Recommended Posts

  • 0

With the transmission in drive the engine RPM should be 525-575 for a 5.7 and 675 - 725 for a 5.0. If your vehicle is within these specs than the pump should be turning fast enough to provide enough pressure to the gearbox.

Have you tried to raise the RPM while parked to see if it turns easier? Any unassisted power steering will feel easier to steer while moving.

Link to comment
Share on other sites

  • 0

Air in system yet!

I think a good way to bleed system is turn steering wheel back and forth (lock to lock) many times and this bleeds system. Or reg. driving!

That or pump has something wrong with it. Line blocked or pinched!

Do you hear any whining noise pr squealing noise when steering wheel is turned.

Did you leave any Elec. wires unhooked at pump or lines?

Link to comment
Share on other sites

  • 0

i talked to the mechanic and they said the pump only pumps when its in demand but theres still gota be something because it never steered that hard with the original pump before it quit and i dont know how they expect you to drive it like it is and no there is no winding noise at all

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.


  • Your Responses - Share & Have Fun :)

    • It’s done automatically.  You might need an actual person to clear that log in stuff up.   Trash your laptop history if you haven’t tried that already.
    • 😂 yea pretty amazing how b o o b i e s gets flagged, but they can't respond or tell me why I  can't get logged in here on my laptop but I can on my cellular  😪
    • I grilled some brats yesterday, maybe next weekend will the next round...  
    • You got word censored cuz you said        B o o b ies….. haha.   Yeah, no… grilling is on hiatus for a bit.
    • Chicken mine,  melded in Mccormick poultry seasoning for 24 hours.  Grill will get a break till the frigid temps go away!
    • we had some nice weather yesterday and this conundrum was driving me crazy  so I drove up to the house to take another look. I got a bunch of goodies via ups yesterday (cables,  winch ratchet parts, handles, leaf springs etc).   I wanted to make sure the new leaf springs I got fit. I got everything laid out and ready to go. Will be busy this weekend with kids stuff and too cold to fish anyway, but I will try to get back up there again next weekend and get it done. I don't think it will be bad once I get it lifted up.    For anyone in the google verse, the leaf springs are 4 leafs and measure 25 1/4" eye  to eye per Yetti. I didnt want to pay their markup so just got something else comparable rated for the same weight.   I am a first time wheel house owner, this is all new to me. My house didn't come with any handles for the rear cables? I was told this week by someone in the industry that cordless drills do not have enough brake to lower it slow enough and it can damage the cables and the ratchets in the winches.  I put on a handle last night and it is 100% better than using a drill, unfortatenly I found out the hard way lol and will only use the ICNutz to raise the house now.
    • I haven’t done any leaf springs for a long time and I can’t completely see the connections in your pics BUT I I’d be rounding up: PB Blaster, torch, 3 lb hammer, chisel, cut off tool, breaker bar, Jack stands or blocks.   This kind of stuff usually isn’t the easiest.   I would think you would be able to get at what you need by keeping the house up with Jack stands and getting the pressure off that suspension, then attack the hardware.  But again, I don’t feel like I can see everything going on there.
    • reviving an old thread due to running into the same issue with the same year of house. not expecting anything from yetti and I already have replacement parts ordered and on the way.   I am looking for some input or feedback on how to replace the leaf springs themselves.    If I jack the house up and remove the tire, is it possible to pivot the axel assembly low enough to get to the other end of the leaf spring and remove that one bolt?   Or do I have to remove the entire pivot arm to get to it? Then I also have to factor in brake wire as well then. What a mess   My house is currently an hour away from my home at a relatives, going to go back up and look it over again and try to figure out a game plan.           Above pic is with house lowered on ice, the other end of that leaf is what I need to get to.   above pic is side that middle bolt broke and bottom 2 leafs fell out here is other side that didnt break but you can see bottom half of leaf already did but atleast bolt is still in there here is hub assembly in my garage with house lowered and tires off when I put new tires on it a couple months ago. hopefully I can raise house high enough that it can drop down far enough and not snap brake cable there so I can get to that other end of the leaf spring.
    • Chef boyardee pizza from the box!
  • Topics

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.