Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. ?

  • 0

Can I Use a Transom Mount Transducer as a Through Hull on an Aluminum Boat?


quijibo

Question

I convinced my Wife to come up to the cabin on our vacation and I just found my transducer broken off from the transom mount. Can I just epoxy/silicone it to the hull? It is an '86 Lund Mr Pike and there is a spot about 10" forward of the transom and 6" to the starboard side that I could either silicone or epoxy it to. The transducer is a Lowrance HST-WSBL from an LCX-25C. I realize that I would lose my water temperature sensor, but is there another reason that this might not work? I've tried searching the net, but there are as many people that say it's works great as there are people that disagree with them.

Link to comment
Share on other sites

6 answers to this question

Recommended Posts

  • 0

It's broke anyway....so you have nothing to lose.

I had a standard "skimmer" ducer epoxied in the bottom of my boat for three year until the epoxy finally popped free. It worked great....and and the bottom of my boat was 0.190 gauge aluminum (twice as thick as yours probably is).

You lose about 10% or so of the sensitivity I'm told.....but I never noticed any signal loss.

Link to comment
Share on other sites

  • 0

Here's how to find out if it will work:

Make a "pond" on your boat bottom with putty. Place the transducer in the pond, fill it with water and go boating. As long as the ducer has water underneath it, it should shoot thru the hull. If not, don't bother epoxying it in.

Link to comment
Share on other sites

  • 0

I tried it and it didn't work, it took about 3 or 4 minutes to get a depth reading and the sonar returns were unintelligible. I did find a replacement transducer(HST-WSBL/106-72) and just spent three hours driving and two hours mounting it and routing the wires. Unfortunately Lowrance uses that same part number for another unit as well, because the connector doesn't fit my unit(LCX-25C). I am really starting to wonder why I keep buying stuff from these guys.

Link to comment
Share on other sites

  • 0

Here's how to find out if it will work:

Make a "pond" on your boat bottom with putty. Place the transducer in the pond, fill it with water and go boating. As long as the ducer has water underneath it, it should shoot thru the hull. If not, don't bother epoxying it in.

I will say that this is not a good test. The transducer has to be solid to the bottom. Try it with silicon before giving up on it. Silicon it to the bottom and allow to set up overnight. Just having it in water is fine if someone is in the back holding it tight to the bottom. Otherwise any gap or vibration will mess up the return signal.

Link to comment
Share on other sites

  • 0
I will say that this is not a good test. The transducer has to be solid to the bottom. Try it with silicon before giving up on it. Silicon it to the bottom and allow to set up overnight. Just having it in water is fine if someone is in the back holding it tight to the bottom. Otherwise any gap or vibration will mess up the return signal.
Shoot through ducers are flat bottom so they sit flat and bond well to the hall bottom. Skimmer duces are rounded a bit to ride in the water better. Unless you can make a solid column for sound to travel from the bottom of the ducer through the hall and to the water you will not get a good reading. But it may work as WWG has suggested. wink
Link to comment
Share on other sites

  • 0

I filled a 3" pvc about half way with clear roofing caulk an embedded the transducer in it. I didn't wait overnight though, maybe I should give it another try. There is only a 9" x 9" area that is open to the hull and it also has a bilge pump and a drain plug in there too, so there was really only one place to mount it without tearing out the floor.

I talked to Lowrance this morning and their records indicate that my new transducer must have been a fluke since they never made one with that connector and pin configuration. They are overnighting(Monday) a new one free of charge. I guess the new owners really are taking their reputation seriously.

I guess I'm fishing old school on this vacation. I wonder what will try to screw with my next trip.

Link to comment
Share on other sites

Join the conversation

You can post now ↓↓↓ or ask your question and then register. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Answer this question...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.