Guests - If You want access to member only forums on HSO. You will gain access only when you sign-in or Sign-Up on HotSpotOutdoors.

It's easy - LOOK UPPER right menu.

Sign in to follow this  
Followers 0
FlatBottom

Rear defrost question

3 posts in this topic

I've got a 2000 Malibu with rear defrost, or now lack there of I guess you could say. The wire has broke away from the element inside the window. Is there any way a guy can reattach that wire or is it a deal were I'd have to replace the window? I don't need it, but it's nice to have especially this morning when there's a ton of frost on the windows.

Share this post


Link to post
Share on other sites

They make a kit where you can reglue/solder the wires back on, also make a kit to paint the lines back on if they are open as well. Any parts store should have them in stock.

Share this post


Link to post
Share on other sites

I have used the paint the line repair stuff with success in the past. The "glue" the terminal stuff has had variable results. it either works great or it doesn't.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now
Sign in to follow this  
Followers 0



  • Posts

    • I've also had good luck spray painting PVC.  Biggest thing I found is to do lots of light coats, the PVC makes the paint want to run in a hurry.
    • I believe you can do this with the Lowrance HDS 9 and above.
    • I'll go with another loss in overtime.
    • Calling a win tonight, it's going to happen!
    •   You'll probably run into plenty of "experts" among the experts, too...   Floor heat is nice, but definitely not the best option if you're looking for the best efficiency, since it is a slow recovery system.  If you were looking for efficiency and lowest cost, I would suggest looking into a mini-split heat pump to complement the gas furnace if you have off-peak available.   (Disclaimer: Not an expert either, but I have stayed at a Holiday Inn Express a few times.)      
    •   Same here. I have 3 of them. Use them in the SUV, Boat, Snowmobile, and Dual Sport bike. They seem to work better on my sled in the winter with no issues at all over my old ifinder which would eat batteries in the cold. They are discontinued but you can still find them out there on the List or bay once in a while. I like them as they are a crossover and can be used on the road or with a lake map which is the main thing I use them for. Wish they would bring something like it back.
    • Ridiculous... but it would work.  Sorry to offend, guess I don't get quite so fired up about concrete.
    • Concrete. Way easier to plow. My parents have a gravel driveway WORST THING EVER! Impossible to snow blow because of all the rocks always wet and muddy. Sure it's cheaper but in the long it's not worth the cheaper price. 
    • I have used a Lowrance XOG (no longer available) on my boat and on my snowmobile for years now with no problems with cold or speed of tracking. I use a Lakemaster card for Minnesota lake for fishing, a Navionics card for coverage in Canada and LOW for winter and summer fishing, and a Red Pine snowmobile trail map for riding. Have ridden at 30 below without any problem with the touchscreen, it is hooked up to sled power, so it probably is getting some heat, and I put it inside my jacket when I get off. I recommend that you do a little research on the available chips for where you are going because different manufacturers use different chips. My use pretty much limits me to Garmin, and expect to pay couple to $300+ for chips for where I travel.
    • So are you saying what happened to me did not happen ? We not talking about a 4 inch concrete slab , it is a thin layer of gyp crete that covers the pex , it has the consistency of water when poured and sets up fast, it is self leveling and any movement in the pex shows up and cant be undone . Yes if it was fastened continuously it could not move but that would be ridiculous . As so this discussion !  
  • Our Sponsors