Guests - If You want access to member only forums on HSO. You will gain access only when you sign-in or Sign-Up on HotSpotOutdoors.

It's easy - LOOK UPPER right menu.

Sign in to follow this  
Followers 0
cRaPpiEMaN8265

Line Diameters

5 posts in this topic

Does anyone know the line diameter of the Cortland master braid in the 80# or 100#? I am deciding whether to get the masterbraid or tufline xp but I think i want something with a larger diameter...

Thanks,

Ryan

Share this post


Link to post
Share on other sites

Tufline XP is made by Western Filament... Cortland is made by Cortland Lines...

as for the info...

heres what I could find

Tufline XP 80 = .018" 100 = .019"

You could send emails to the companies asking for info... I dont think Cortland makes 100# for their Masterbraids yet... just 80# and 130#

Share this post


Link to post
Share on other sites

Hey Reb,

Thorne does have the Masterbraid in the 80 and 100lb. I don't know the exact specs, but I really can't tell a difference between it and other 80lb braids. I do think it packs the spool better than any other braid, so I would not be concerned about it's diameter and the potential plus/neg to performance.

Share this post


Link to post
Share on other sites

Chris...

I did look at Cortland HSOforum... and dont see 100# anywhere... but guess that HSOforum needs to be updated... Thanks for rectifying the info...

Share this post


Link to post
Share on other sites

Most of the Super Braids have roughly the same diameter. XP and Masterbraid in 80# are both 18# mono equivalent.

Aaron

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  
Followers 0



  • Posts

    • Had an 09'. Got rid of it. Also,  you could not keep the front end aligned.  Otherwise a very nice truck.
    • Helps when I comprehend what I read.  I actually just cut the handle off my tongue jack on my Yetti and welded on 3/4 nut too.  My M18 drill with 1,200 in-lbs (2704-20) and it has no problem raising or lowering the tongue.  Biggest thing I noticed was making sure my drill was on the #1 low speed setting.      As far as torque goes and harming your auger.  I think you are totally fine and shouldn't harm anything.  The max amount that these K-Drills and Clam plates are drilling these days with the big drills are 8".  Most sized augers these days have no problem turning a 10" auger which is nearly twice as large of an area than an 8" auger.  Being 2 strokes can normally operate in any orientation without being damaged the only concern I would have would be your gears and any shifting of grease inside operating the auger head on its side under load.    They say Ions will do 10" holes but after I talked to their customer service reps about it, I wouldn't trust an Ion with a 10" more than I do a wet fart.  Just the fact that they don't even sell a 10" package indicates there could possibly be issues with torque and reliability when operating the 10" auger "accessory".  For now I'd just stick to your strike master going up and save your Ion any extra wear and tear.  Maybe even ask Santa for some electric jacks this Christmas
    • As the media begins to draw a pretty picture about the November jobs report, namely that unemployment has dropped to 4.6 percent, its lowest level in nine years, they are unlikely to tell you the other part of the story. The labor force participation rate continues to decline and is stuck at a rate we haven't seen since February 1978, according to the Bureau of Labor Statistics.  It gets worse. Last month, we lost 4,000 manufacturing jobs, offering more damage to the already 301,000 we've lost since President Obama took office. - Town Hall   See for yourself.. U.S. Dept of Labor / BLS Date Viewer   Whaaa ???   OH, MY....  
    • I wouldn't do that for each one. I was wondering if you couldn't cut a winch down, or maybe just leave it as is, so you could attach a drill to the low speed post and tack weld/rig a socket or something for the other side and just hold it in your hand. It probably won't work because it sounds too easy. 
    • My, such big words!! Yer a talented liddle Smurf, aintcha? We might as well get to work doin' what we were accused of, munchkin!!! Like Carly Simon said, "no one does it better"....  
    • i,ve been falsey accused of inproprieties!!!!!!!!!!!
    • Ken W, I have that book too. Before the internet it was really tough to find info. about sausage making. I never had luck getting a tangy flavor using Fermento. The sausage was very good though.
    • Jacks work very smooth, fresh grease and by hand feels fine for the amount of weight.  I think for the winter we'll just use the gas auger up and the hand drill down.  I don't want to sink another penny into these darn jacks if I can help it, should be swapping out by next year.  I may look into the gear reduction but I feel like trying to throw one of them on each of the jacks could add another 100 that could go toward electric.  leech if you ever stumble on that video post the link so I can see what hes doing different.  Works great on the tongue when it can pivot on the wheels but when lifting the full weight of the house at the back two jack points it just doesnt cut it.
  • Our Sponsors