Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. ?

Freelining?


Recommended Posts

Recently I was introduced to freelining with a floro leader and circle hook by a saltwater fisherman. I did a little research and found some people use the technique for Bass. I was wondering if anyone had any experience doing this for Pike in the spring in skinny water. Best live bait? Hooked in the back or snout? Leader test? Best conditions? Etc.

Link to comment
Share on other sites

we have done this once or twice. always live suckers and hooked in tail. we only used 12 lb mono. I would prefer calm days as slack is less of an issue. Hooking fish in tail allowed minnow to swim more freely and we didn't have issues with hook set's.

Link to comment
Share on other sites

People use it for bass???? I'm assuming that they keep the bass.

Anyway, not familiar with the term or maybe I just forgotten about it, since I've gone pretty much artifical lures. I think this is where you thread line (or dental floss) into bait and then tie end of line onto hook shank. Typically with suckers, they're threaded through the nostrols or about's that area. It's a little easier to control bait when they're pulled from the head. If it's really lively bait, then I can see hook attached from tail end. They're more likely to struggle/swim about in place. Easier to keep them from burying in weed.

Link to comment
Share on other sites

The way I was shown was simply braid-double uni to 30# floro- clinch to circle hook. No weight, no float, no floss. Rig a sardine through the nostrils for Snook in mangrove roots and Redfish/Trout over grass. The Sardines were netted wild and would go crazy (sometimes try to break the surface) when a fish was near and even swim back to the boat at which point you'd pitch 'em back in. When the fish picked it up you'd just reel up the slack and start the fight. Whenever I TRIED to set the hook I'd lose the fish more often than not. If near cover, you had to pull them out fast. I don't know how much of that would translate to Pike and Suckers(or big Redtails etc.).

The Bass guys (that I read about) rig 'em through the back and use them around docks. I believe they were releasing the fish. I will say that every fish that I caught was hooked cleanly in the corner of the mouth. I was kind of banking on the bait roaming around some. Good point on the weed problem. Maybe it wouldn't be so bad with early weeds.

Link to comment
Share on other sites

Sounds more and more like just free swimming live bait.

I've only occassionly use circle hooks and one thing about them, is that you do also need to set the hook. That's after the circle hook, hooks the fish. You need to ensure the hook point, drives through rather than just simply lip stick a little flesh.

The shape of a pike's mouth function a lot like a clamp. You don't want to simply just reel up and start fighting the fish. You need to feed them some line and let them run with it, because often the bait is just clamped in their mouth. It's when they've swallowed the bait, or engulf it deeper, do you set the hook. In the case of a circle hook, they work better if the fish's lips are sealed, or your line is in the mouth cornered (which is often).

It's weird to hear this a method for bass, but plausible for the more lethargic floridian strain lmb's. For the norther strain, you're more than likly having to uproot some weeds and a lot more harder for downed timber. Anyway when artificials fail and that leaves live bait, then the tight lipped bass may fit the lethargic category.

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.


  • Your Responses - Share & Have Fun :)

    • got this tackled today took about 3 hours to get both sides done. Didnt even get to use a torch....   Thought I was golden with just jacking it up and I could get to everything but no luck. Had to remove the entire axle hub and brake assembly to get to what I needed. Was a pain but still better then taking off the entire pivot arm.    Axle bearings were already greased and in great shape thankfully. Got both leaf springs installed and its ready for the road again.   Probably going to have my electric brakes checked, I am not touching anything with the brake drums. Based on what I saw it doesn't look like my electric brakes have been working anyway. Brakes are nice to have if its slippery out
    • By The way that didn't work either!! Screw it I'll just use the cellular. 
    • It’s done automatically.  You might need an actual person to clear that log in stuff up.   Trash your laptop history if you haven’t tried that already.
    • 😂 yea pretty amazing how b o o b i e s gets flagged, but they can't respond or tell me why I  can't get logged in here on my laptop but I can on my cellular  😪
    • I grilled some brats yesterday, maybe next weekend will the next round...  
    • You got word censored cuz you said        B o o b ies….. haha.   Yeah, no… grilling is on hiatus for a bit.
    • Chicken mine,  melded in Mccormick poultry seasoning for 24 hours.  Grill will get a break till the frigid temps go away!
    • we had some nice weather yesterday and this conundrum was driving me crazy  so I drove up to the house to take another look. I got a bunch of goodies via ups yesterday (cables,  winch ratchet parts, handles, leaf springs etc).   I wanted to make sure the new leaf springs I got fit. I got everything laid out and ready to go. Will be busy this weekend with kids stuff and too cold to fish anyway, but I will try to get back up there again next weekend and get it done. I don't think it will be bad once I get it lifted up.    For anyone in the google verse, the leaf springs are 4 leafs and measure 25 1/4" eye  to eye per Yetti. I didnt want to pay their markup so just got something else comparable rated for the same weight.   I am a first time wheel house owner, this is all new to me. My house didn't come with any handles for the rear cables? I was told this week by someone in the industry that cordless drills do not have enough brake to lower it slow enough and it can damage the cables and the ratchets in the winches.  I put on a handle last night and it is 100% better than using a drill, unfortatenly I found out the hard way lol and will only use the ICNutz to raise the house now.
  • Topics

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.