Just found this forum. Figured I'd start rifling your archives for some info and ask some questions.
I think I have to replace my X60, so I've begun looking for a new setup.
Fshing that I do is usually confined to depths of less than 20 feet (I'm having a tough time thinking of the last time I was in water even 40 feet deep). Most of my fishing is in rivers and reservoirs. Most are fairly stained (not clear).
I'm hoping to get around problems I had in the past with the X60. Obvious ones were...in high spring water below dams...I had a tough time getting good image of anything but the bottom. Suspended particulate matter and other crud in the current I think pushed the thing to the limit. I had to mess with clarity and everything else to try and remove surface clutter, but I always figured I was removing fish, weeds, etc. To a lesser extent, I think this problem also appears in murky rivers with less current, but that still have lots of suspended crud.
So, now I'm looking.
Old prejudices die hard...but I think Humminbird is out of the picture.
From units I've seen, I'm thinking of a Lowrance x125, a Garmin 250, or Eagle 320 or 480's.
From quickie observation, the 250 had the easiest to read screen (in a store...not in sun), followed by the 480 and then the 125. Aside from that, I don't have much background on these suckers anymore, so my questions:
1) For the depths and type of water I fish, how much wattage is too little or too much. 2) What type of transducer would you guys be looking for (skimmer/puck, cone angle) 3) Any known issues with these units that would make you say "don't bother with this one?" 4) Any units I should consider instead? (I sort of considered the X51, X58, etc...but the menus looked like a pain to deal with) 5) On color units (like a 250C), is the unit's ability to discern fish any better than a tuned b&w with grayscale?
Well, that's enough bugging you for now. Thanks for your help.
[This message has been edited by Carphunter (edited 06-16-2004).]
I just figured that it is easy enough to just get a 3 bank so when the boat is not in use I can keep all 3 batteries charged. I have not bough a charger yet, maybe I will give it some more thought.
Edit: After thinking this over, with the size, weight, and heat output of the charger (as well as the cost) I think it makes sense to just
buy a 2 bank charger, I have a smaller charger i can use on the starting battery when the boat is sitting at home. Forgive me, for i am a retired engineer and I have to obsess over everything...
Congrats on the motor! I think you’ll like it.
I can’t say much on the charger location but I’ve seen them under the lid in back compartments and under center rod lockers. 160 degrees is more than I expected to hear.
Curious why you’re opting for a 3 bank charger with a 24V trolling motor. Unless you don’t feel you be running you big motor enough to keep that battery up as well?
I did buy an Minnkota Ulterra, thanks for the recommendations. I had a bunch of Cabela"s bucks saved up, which helped. Now i need to
get an onboard battery charger. Where do you guys mount these things in your boat? The manufacturer I am looking at {Noco genius)
says tht their 3-bank charger will run at 160 degrees, seems like a lot of heat in an enclosed compartment? Thanks for any input on this.
Wasn't terrible at a state park beach. Antelope island maybe. I wouldn't recommend it as a beach destination tho. Figured I was there, I'm getting in it.
Question
Carphunter
Just found this forum. Figured I'd start rifling your archives for some info and ask some questions.
I think I have to replace my X60, so I've begun looking for a new setup.
Fshing that I do is usually confined to depths of less than 20 feet (I'm having a tough time thinking of the last time I was in water even 40 feet deep). Most of my fishing is in rivers and reservoirs. Most are fairly stained (not clear).
I'm hoping to get around problems I had in the past with the X60. Obvious ones were...in high spring water below dams...I had a tough time getting good image of anything but the bottom. Suspended particulate matter and other crud in the current I think pushed the thing to the limit. I had to mess with clarity and everything else to try and remove surface clutter, but I always figured I was removing fish, weeds, etc. To a lesser extent, I think this problem also appears in murky rivers with less current, but that still have lots of suspended crud.
So, now I'm looking.
Old prejudices die hard...but I think Humminbird is out of the picture.
From units I've seen, I'm thinking of a Lowrance x125, a Garmin 250, or Eagle 320 or 480's.
From quickie observation, the 250 had the easiest to read screen (in a store...not in sun), followed by the 480 and then the 125. Aside from that, I don't have much background on these suckers anymore, so my questions:
1) For the depths and type of water I fish, how much wattage is too little or too much.
2) What type of transducer would you guys be looking for (skimmer/puck, cone angle)
3) Any known issues with these units that would make you say "don't bother with this one?"
4) Any units I should consider instead? (I sort of considered the X51, X58, etc...but the menus looked like a pain to deal with)
5) On color units (like a 250C), is the unit's ability to discern fish any better than a tuned b&w with grayscale?
Well, that's enough bugging you for now. Thanks for your help.
[This message has been edited by Carphunter (edited 06-16-2004).]
Link to comment
Share on other sites
6 answers to this question
Recommended Posts