Jae
-
Posts
33 -
Joined
-
Last visited
Never
Everything posted by Jae
-
buddy tried it likes it but to much cash for so little line
-
id check tie rod, ball joint, any boots if cracked or torn, powerstearing fluid, check the alignment, shock and mount, and mabe the wheel bearing.
-
mine does it sometimes almost looks like it resets or goes off then on quick a pita sometimes when it counts
-
with any fast curing epoxy you are going to get bubbles or yellowing, 24hr is better, and high spots, most of the plug builders seal the plugs ie waterproofing the wood b4 priming them with Helmsman Satin - do not use gloss - Spar Urethane cut 60/40 with Mineral Spirits, or Helmsman Spar Uerathane cut 50/50 with Mineral Spirts, dip them for 1 to 2 minutes and wipe off the excess and hang them to dry for a day or two. or etex (envirotex), u could also try flexcote after u paint the lure as a clear coat
-
i dont think it matters, u may want to run a slightly richer oil to gas, mabe a heavy 40:1 for the first tank then run amsoil saber 80:1 or 100:1 and should be good to go.
-
?Oil mess on strikemaster augers?
Jae replied to Mike Stark's question in Equipment-Expert Information*
when season over take muffler off let it soak or spray the [PoorWordUsage] outa it with brake cleaner or carb cleaner or some type of solvent. this will get rid of the heavy deposits, and im gona try and use my torch to see if i can burn the [PoorWordUsage] outa my muffler at the end of the season -
update, went upstate ny fishing the hard water, the auger worked ok but not great, hard time punching through the last inch or so and still had the throttle issue, ripped the carb apart today and found that the diaphram was warped in a way that it was blocking the pin that opens the needle, replaced now she works fine, good throttle response ect. will try her on some ice this week or weekend and see if that was the main problem
-
Did my Toro snowblower just die?
Jae replied to Gadgetman's question in Equipment-Expert Information*
i second seized motor -
i have a H&R slug gun with a 4.5x scope works fine for me but tried many different slugs, ie weight and velosity and have found that the federal 2 3/4" w/barnes slug works best with a 1480fps (cant rember exact) faster slugs seemed to go al over the place @ 100+yds but i feel that my most effective range is between 25-75 yds for a nice clean kill
-
A heck fo a deal - dishwasher question
Jae replied to Tom7227's question in Equipment-Expert Information*
when i take off the kick plate, ie panel under the door to the dish washer, there is a hose that is notiorous for getting chewed up by mice or other. that may be leaking as this has happened to mine, solved that problem fast with dcon and 8 snap traps, 4kia. but id check the hose first, take the kick plate off and run the rinse cycle and see where it is comming from -
the reason its doing that is its taking a long time to load the buffer, or memory the computer needs to play the video. it may be ur internet connection is becoming slow or mabe ur computers cookies/temp folder needs to be emptied, and or u may have some spyware affecting the preformance of ur internet. a possible solution would be to pause the video till the red line, witch indicates how much of the video has been uploaded moves mabe 1/4" or so. this should be a temp fix, scan comp for spyware/virus
-
Solo auger handle problems
Jae replied to Whopper Stopper's question in Equipment-Expert Information*
have heard the handles that are plastic tend to break when dropped from minimal height -
ran a mix of 93 oct w/amsoil 100:1 a cap full of seafoam. noticed a slight difference when the old 87 oct 40:1 left the system. had to bring the idle up a little as i let it idle for a few minutes and it wanted to stall throtle well idk when i hit the thumb bar it goes from idle to almost a stall/bogs down then goes wot
-
Can I put a Lazer hand auger bit on my powerhead?
Jae replied to Dozer's question in Equipment-Expert Information*
slow start the hole as the hand sm dont have a center pin and the bit could hop and turn ur foot into ground chuck -
i want the powerhead that they have here @ 2:05 thats how i want my auger to run
-
jim the auger either doesnt break threw the bottom of the hole or corkscrews threw the bottom, i just let the weight of the auger push it down. and as for non oxy ive never seen it by me. as for shimming it its gona have to wait lots of rain this way and warm weather not so good for the ice and i may have to use the 14' 2x12 to get on. i should be headed to up state ny next week so i may be able to get non oxy up there and ill get a good test, but im gona make up a batch of high test and amsoil here with some seafoam to clean out the fuel system
-
new blades are doing the same thing as the old ones, the pitch may be wrong, i talked with a tech and he said put new blades on and if that doesnt work its probably the pitch. so i may be sending the auger to them, not the powerhead. also idk where to get non oxy gas by me, as im on the east coast
-
making the switch to amsoil saber 100:1 in my lazer mag express. questions are reg gas or high test, stock spark plug or upgrade, possible carb adjustments, and other things to get this thing running right as im getting mad at it, binding at the bottom of the hole, new blades so pitch may be wrong, may go back, and auger speed is lacking.
-
went to a spot i havent fished since last year and banged the smallies, got 14 dropped 6 and 1 pearch outa the same hole in about 4 1/2 hours, went and used old reliable.
-
irish i havent heard of this but i have had activity when i drop down a jiggin rap, only to have the sunny suck the side of the jig, i saw it on my camera, and i was p!$$3d lol. btw no drinking 4 me, seen to many bad things happen with smashed people and fishing the surf, its funny but kinda sad if u think about it.
-
idk harvey i think i had a lemon, thats y i have a lx5 now ;P
-
lately in a few lakes by me the fish seem to have lockjaw. ive tried big to micro jigs, spikes and plastics, different colors bright to black, all the glow colors, rattles no rattles, horizontal, and verticle, silver and gold, i just wanted to see what some of u guys do when this happens, this doesnt happen often to me at the lakes i fish. i also move often, mod bite 15-20 holes, on a slow bite 60+
-
had the 45 but it would randomly reset screen would go black just like when u turn it on, returned it and got a lx3tc then the ducer broke returned and got the lx5. the bird was cool but it was being a pita when it counts. nice features on em though easy to read but picks up interference from vex and marcums, was tough to get rid of even with the ir rejection, easy to read, and gived u an accurate depth
-
any one play the pc version? if u want to shoot me a steam friends invite name is EvilJin
-
cant figure this one out i got brake lights and hazards but when i turn the left or right turn on the hazards coome on the trailer im baffled?!?! replaced my coroded 4 pin on the truck and new harnes on the trailer im so comfused