Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. ?

  • 0

Mr Heater thermocouple


Dave

Question

Was on Mille Lacs last weekend. Wow, what a rough ride. I had the Mr. Heater in the Otter Sled. The thermocouple broke off right at the valve. The places I've checked, so far, are out of them. Any way to repair this one or can I just remove it and not use this safety option.

Link to comment
Share on other sites

8 answers to this question

Recommended Posts

  • 0

I had this happen to me once. In an emergency situation on the ice I took a piece of string and tied it around the base to the safety "plug" or whatever you call it, the button that you push to warm up the unit before it works on its own.
I then took duct tape and permanently taped the button shut and used the on/off, low, high switch until I bought a new unit. Seemed to work just fine without the thermo. I couldn't see a way to fix it as I obviously could not weld the thermo base back one to the sunflower head.

Link to comment
Share on other sites

  • 0

My cousin was working on a heater and he used tie straps. But this is only a quick short time fix. The problem he had was that the thermocouple that was installed was rated higher than the heater itself - it wouldn't stay lit. So when you get one make sure that it is the proper rated thermocouple.

Link to comment
Share on other sites

  • 0

The thermocouple is what allows the gas to flow through the gas valve which is the button valve you are refering to. If your getting gas to flow without using the t-couple or holding the button down, then your gas valve is faulty. If the flame were to go out, you will be dumping raw LP. Take the old t-couple to any menards,home depot or hardware store and match the proper length. They are around $6-$10. Depending on how old your heater is you may want to buy a new heater.Walmart in Fridley had them last week for $36.00 Good Luck

------------------
MILLE LACS AREA GUIDE SERVICE
651-271-5459 http://fishingminnesota.com/millelacsguide/

[This message has been edited by D-man (edited 01-30-2002).]

Link to comment
Share on other sites

  • 0

I broke my thermocouple at the end of last year when they were off the shelves for the season. I just taped the button down and ordered one directly from Mr. Heater. When I got it I never ended up fixing it. I just left it the way it was. I'm never in a situation to worry about having the safety feature of the couple.

Link to comment
Share on other sites

  • 0

Thanks for the offer hunt4food but, there's a gas place down the road that should have one. I'll go there tomorrow and if I'm out of luck on finding one, I'll let ya know.

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.


  • Your Responses - Share & Have Fun :)

    • Your kid needs to stay with him!👍
    • My kid was eating in Beverly Hills and ran into this guy. Talked to him a bit and wished him luck in the game tonight.     
    • 🤔as a recovering machinist!🤣🤣that must make me a recovering welder!
    • As a recovering machinist, I can appreciate that.  If the spec is 0.001 - 0.0015, then clearly the correct measurement is 0.00125, duh…
    • I just figured that it is easy enough to just get a 3 bank so when the boat is not in use I can keep all 3 batteries charged. I have not bough a charger yet, maybe I will give it some more thought. Edit: After thinking this over, with the size, weight, and heat output of the charger (as well as the cost) I think it makes sense to just buy a 2 bank charger, I have a smaller charger i can use on the starting battery when the boat is sitting at home. Forgive me, for i am a retired engineer and I have to obsess over everything...
    • Congrats on the motor!  I think you’ll like it.   I can’t say much on the charger location but I’ve seen them under the lid in back compartments and under center rod lockers.  160 degrees is more than I expected to hear.   Curious why you’re opting for a 3 bank charger with a 24V trolling motor.  Unless you don’t feel you be running you big motor enough to keep that battery up as well?
    • I did buy an Minnkota Ulterra, thanks for the recommendations. I had a bunch of Cabela"s bucks saved up, which helped. Now i need to get an onboard battery charger. Where do you guys mount these things in your boat? The manufacturer I am looking at {Noco genius) says tht their 3-bank charger will run at 160 degrees, seems like a lot of heat in an enclosed compartment? Thanks for any input on this.
    • You're very lucky a troop of Sea Monkey's didn't carry you away.   
    • Wasn't terrible at a state park beach. Antelope island maybe.  I wouldn't recommend it as a beach destination tho.  Figured I was there, I'm getting in it.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.