Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. ?

Homemade French Fries


Recommended Posts

Whats the key to getting homemade french fries to stay crispy after they are out of the fryer? Mine are crispy when I first bring them out but after the oil drains off of them they get a little soggy. I have heard to soak them in vinegar prior to frying, is this true?

Link to comment
Share on other sites

I like to cook them through not golden (6 min at 350 roughly..) then pull them out and let them cool on a rack on the counter or in the fridge... once cool fry them again until they are done.... CRISPY FRIES! Twice Fried wink.. I hope there are some other good ideas.. I love making fries.

Link to comment
Share on other sites

Tips:

Cut and dry them off (prior to frying) between layers of paper towels to remove H2o and excess starch.

Use Peanut Oil

Fry at 360 degrees

Always fry twice--first to cook them, let cool and then to crisp and brown them just before serving.

Fry in small batches so they stay apart and the oil stays hot.

Link to comment
Share on other sites

Ingredients

For the Potatoes:

4 large Russet potatoes, about 2 pounds, peeled

Peanut oil, for frying

Salt

Special equipment: electric deep fryer or large heavy pot with deep-fry thermometer

Directions

Potato Preparation: Fill a large heavy pot with enough oil to reach halfway up the pot being mindful not to overfill the pot. You don't want oil to overflow from the pot when you're cooking the fries. Attach the thermometer to the side of the pan. Heat oil over medium heat until it reaches 325 degrees F.

Meanwhile, fill a large bowl with water. Square off the potatoes and cut them into sticks about 1/4-inch thick and the length of the potato. Place sticks in the water. Drain potatoes and dry well with paper towels. This will prevent splattering of hot oil.

Working in batches, add a handful of potatoes to the preheated oil. Fry for 5 to 6 minutes giving the potatoes a chance to cook on the inside without developing much color on the outside. Remove to a paper towel lined plate. Bring the oil back up to 325 degrees F before adding the next batch. Repeat until all batches are complete.

Let fries cool completely. Meanwhile, bring oil up to 375 degrees F. Add potatoes to oil again in batches until nicely golden, about 1 minute.

Link to comment
Share on other sites

If you can flash freeze them like the commercial ones, they should be fine, but I'd try a small batch first to see exactly what they'd turn out like to see if you like the quality.

There are so many ways the commercial ones are prepped that we can't do, e.g., chemicals, freezing process. A lot of engineering goes into the process that we just can't replicate at home.

If you try it, let us know how it goes.

Link to comment
Share on other sites

As I've found with hashbrowns (and other potatoes), the key to making them crispy is getting the water out of them. As others have stated, really get them dry before frying. You can also bake them in the oven for the cooking part and then fry them to get them crispy and golden-brown.

Link to comment
Share on other sites

Depeds on how thick they are. If you're making a fry that's about 1/2" thick, pre-bake them after tossing them with Peanut Oil, Salt&Pepper on non-stick foil for about 20-30 minutes at 400 degrees in the center rack of your oven.

Link to comment
Share on other sites

the key to a crunchy fry is to keep the oil HOT! As said in previous posts cut them and then put them in water. Drain the water (this will take some of the starch out of the fries. Blanch them or partially cook them until the white is completely out of the fries.Cool them and then cook them again. When you cook them a second time make sure your oil is at 375 degrees.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Your Responses - Share & Have Fun :)

    • Yeah it was a beatdown
    • Your kid needs to stay with him!👍
    • My kid was eating in Beverly Hills and ran into this guy. Talked to him a bit and wished him luck in the game tonight.     
    • 🤔as a recovering machinist!🤣🤣that must make me a recovering welder!
    • As a recovering machinist, I can appreciate that.  If the spec is 0.001 - 0.0015, then clearly the correct measurement is 0.00125, duh…
    • I just figured that it is easy enough to just get a 3 bank so when the boat is not in use I can keep all 3 batteries charged. I have not bough a charger yet, maybe I will give it some more thought. Edit: After thinking this over, with the size, weight, and heat output of the charger (as well as the cost) I think it makes sense to just buy a 2 bank charger, I have a smaller charger i can use on the starting battery when the boat is sitting at home. Forgive me, for i am a retired engineer and I have to obsess over everything...
    • Congrats on the motor!  I think you’ll like it.   I can’t say much on the charger location but I’ve seen them under the lid in back compartments and under center rod lockers.  160 degrees is more than I expected to hear.   Curious why you’re opting for a 3 bank charger with a 24V trolling motor.  Unless you don’t feel you be running you big motor enough to keep that battery up as well?
    • I did buy an Minnkota Ulterra, thanks for the recommendations. I had a bunch of Cabela"s bucks saved up, which helped. Now i need to get an onboard battery charger. Where do you guys mount these things in your boat? The manufacturer I am looking at {Noco genius) says tht their 3-bank charger will run at 160 degrees, seems like a lot of heat in an enclosed compartment? Thanks for any input on this.
    • You're very lucky a troop of Sea Monkey's didn't carry you away.   
    • Wasn't terrible at a state park beach. Antelope island maybe.  I wouldn't recommend it as a beach destination tho.  Figured I was there, I'm getting in it.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.