Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. ?

deep cycle battery question


vizsla01

Recommended Posts

Usually, for batteries where you add water, there are like extensions on the bottom of the holes where the cell caps go in. The proper water level is at the bottom of those extensions so the water is just touching them.

Distilled water is preferred/recommended...

Link to comment
Share on other sites

Distilled water for sure. Using regular water will allow the minerals contained in it to attach to the lead plates with over time (and dependent on the amount of water of course) will reduce your batteries efficiency.

As far as level, I've always filled the cells to the bottom of the cell plug receptacle, there often is a groove cut from the top to the bottom, just until it touches the bottom and it seems like the liquid 'puckers' a bit. Hope that made sense.... confused.gif

Link to comment
Share on other sites

Quote:

Distilled water for sure, or if you can find electrolite at a battery place all the better.


What is electrolite? Acid? I was told to never add acid to a battery other than when originally filling them.

Link to comment
Share on other sites

Waskawood - was thinking more about electrolyte and my answer. Did a bit of checking and I'm wrong, you should only add electrolyte to new unfilled batteries then charge. Seems adding it to replace evaporated water will alter the chemical make up (makes it stronger, which is logical) and actually reduces plate life of the battery.

My bad blush.gif, just stick w/distilled (I edited off my poor advice on the earlier post...)

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.


  • Your Responses - Share & Have Fun :)

    • Yeah it was a beatdown
    • Your kid needs to stay with him!👍
    • My kid was eating in Beverly Hills and ran into this guy. Talked to him a bit and wished him luck in the game tonight.     
    • 🤔as a recovering machinist!🤣🤣that must make me a recovering welder!
    • As a recovering machinist, I can appreciate that.  If the spec is 0.001 - 0.0015, then clearly the correct measurement is 0.00125, duh…
    • I just figured that it is easy enough to just get a 3 bank so when the boat is not in use I can keep all 3 batteries charged. I have not bough a charger yet, maybe I will give it some more thought. Edit: After thinking this over, with the size, weight, and heat output of the charger (as well as the cost) I think it makes sense to just buy a 2 bank charger, I have a smaller charger i can use on the starting battery when the boat is sitting at home. Forgive me, for i am a retired engineer and I have to obsess over everything...
    • Congrats on the motor!  I think you’ll like it.   I can’t say much on the charger location but I’ve seen them under the lid in back compartments and under center rod lockers.  160 degrees is more than I expected to hear.   Curious why you’re opting for a 3 bank charger with a 24V trolling motor.  Unless you don’t feel you be running you big motor enough to keep that battery up as well?
    • I did buy an Minnkota Ulterra, thanks for the recommendations. I had a bunch of Cabela"s bucks saved up, which helped. Now i need to get an onboard battery charger. Where do you guys mount these things in your boat? The manufacturer I am looking at {Noco genius) says tht their 3-bank charger will run at 160 degrees, seems like a lot of heat in an enclosed compartment? Thanks for any input on this.
    • You're very lucky a troop of Sea Monkey's didn't carry you away.   
    • Wasn't terrible at a state park beach. Antelope island maybe.  I wouldn't recommend it as a beach destination tho.  Figured I was there, I'm getting in it.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.