Guests - If You want access to member only forums on HSO. You will gain access only when you sign-in or Sign-Up on HotSpotOutdoors.

It's easy - LOOK UPPER right menu.

Sign in to follow this  
Followers 0
Inthehollow

what paint gun

3 posts in this topic

Looking at getting a paint gun for finishing wood work and interior doors what style,brand and tip size any other sugestions would be great thanks Bret

Share this post


Link to post
Share on other sites

Just buy a cheap Binks number seven knock off. As long as you keep it clean it will serve you well for at least 5 years and then when it dies you can go and buy another for 19.99 at the surplus tool sale.

Share this post


Link to post
Share on other sites

depends if your planning on spraying oils or acrylics. also acrylics are more abraisive so over time the tips will wear out- the husky at homedepot will spray acrylics. the only problem is getting enough cfm to use em- good luck--- most guns have a knob to adjust the pattern and the volume of liquid going through, also most have different size orafaces for oils/acrylics- make sure you use an inline dryer, if you dont youll get water spots on your work

Share this post


Link to post
Share on other sites
Sign in to follow this  
Followers 0



  • Posts

    • I've also had good luck spray painting PVC.  Biggest thing I found is to do lots of light coats, the PVC makes the paint want to run in a hurry.
    • I believe you can do this with the Lowrance HDS 9 and above.
    • I'll go with another loss in overtime.
    • Calling a win tonight, it's going to happen!
    •   You'll probably run into plenty of "experts" among the experts, too...   Floor heat is nice, but definitely not the best option if you're looking for the best efficiency, since it is a slow recovery system.  If you were looking for efficiency and lowest cost, I would suggest looking into a mini-split heat pump to complement the gas furnace if you have off-peak available.   (Disclaimer: Not an expert either, but I have stayed at a Holiday Inn Express a few times.)      
    •   Same here. I have 3 of them. Use them in the SUV, Boat, Snowmobile, and Dual Sport bike. They seem to work better on my sled in the winter with no issues at all over my old ifinder which would eat batteries in the cold. They are discontinued but you can still find them out there on the List or bay once in a while. I like them as they are a crossover and can be used on the road or with a lake map which is the main thing I use them for. Wish they would bring something like it back.
    • Ridiculous... but it would work.  Sorry to offend, guess I don't get quite so fired up about concrete.
    • Concrete. Way easier to plow. My parents have a gravel driveway WORST THING EVER! Impossible to snow blow because of all the rocks always wet and muddy. Sure it's cheaper but in the long it's not worth the cheaper price. 
    • I have used a Lowrance XOG (no longer available) on my boat and on my snowmobile for years now with no problems with cold or speed of tracking. I use a Lakemaster card for Minnesota lake for fishing, a Navionics card for coverage in Canada and LOW for winter and summer fishing, and a Red Pine snowmobile trail map for riding. Have ridden at 30 below without any problem with the touchscreen, it is hooked up to sled power, so it probably is getting some heat, and I put it inside my jacket when I get off. I recommend that you do a little research on the available chips for where you are going because different manufacturers use different chips. My use pretty much limits me to Garmin, and expect to pay couple to $300+ for chips for where I travel.
    • So are you saying what happened to me did not happen ? We not talking about a 4 inch concrete slab , it is a thin layer of gyp crete that covers the pex , it has the consistency of water when poured and sets up fast, it is self leveling and any movement in the pex shows up and cant be undone . Yes if it was fastened continuously it could not move but that would be ridiculous . As so this discussion !  
  • Our Sponsors