Jump to content
  • RECEIVE THE GIFTS MEMBERS SHARE WITH YOU HERE...THEN...CREATE SOMETHING TO ENCHANT OTHERS THAT YOU WANT TO SHARE

    You know what we all love...

    When you enchant people, you fill them with delight and yourself in return. Have Fun!!!

Sign in to follow this  
upnorth

2000 silverado service engine light

Recommended Posts

The truck is a 2000 silverado 2500, 6.0l, 130,000 miles. I am getting a service engine light when I am at cruising speed over 55 MPH, It doesn't come on until I am over 55 mph and it goes off as soon as it gets below 50 mph. Takes about 2 minutes of driving over 55 when I first start out, but after that as soon as I reach something over 55 it comes on. If I accelerate fairly hard it goes off til I level off again. No symptoms that I can detect, runs smooth at all speeds, plenty of power and idles fine.

Anyone got any idea of what I am looking at?

Share this post


Link to post
Share on other sites

The truck is just telling you not to drive over the speed limit grin

Share this post


Link to post
Share on other sites

I would say it could be anything from a TQ issue to an emissions issue.

I have not seen this/or recall it in the past with other makes. Could be anything.

I would have a code scan done to see what is found.

Share this post


Link to post
Share on other sites

The truck is just telling you not to drive over the speed limit grin

Good one cool

Share this post


Link to post
Share on other sites

I would say it could be anything from a TQ issue to an emissions issue.

I have not seen this/or recall it in the past with other makes. Could be anything.

I would have a code scan done to see what is found.

I kinda figured I was going to have to have it scanned, just thought by chance I could avoid it.

Share this post


Link to post
Share on other sites

Sorry I am not a Chevy guy, so I was hoping someone else would have your answer, because that was the best one I had whistle . I would pull codes on it and go from there, atleast we would have a direction to go in.

Share this post


Link to post
Share on other sites

Anyone got any idea of what I am looking at?

A 2000 silverado 2500, 6.0l, 130,000 miles on the rack with a scan tool attached! grin

There are literally thousands of possibilities that can turn the check engine light on. The first step is to identify the code and then the fun begins! What happens if you set the cruise at 45 for the same amount of time it takes for the light to come on at 55?

Share this post


Link to post
Share on other sites

Quote:
Originally Posted By: upnorth

Quote:
Anyone got any idea of what I am looking at?

A 2000 silverado 2500, 6.0l, 130,000 miles on the rack with a scan tool attached!

That did make me laugh grin

Share this post


Link to post
Share on other sites

Sorry upnorth, I'm in one of those sarcastic moods today for some reason?

No worries....I have not lost my sense of humor smirk

It stays off as long as I am under 55 MPH. Doesn't matter how far or long I drive it.

Share this post


Link to post
Share on other sites

I may not be able to have it checked for a bit, but when I get something I will post what I get.

And if I am doing over 55 mph and slow down to under 50 mph it goes off.

Share this post


Link to post
Share on other sites

I would say if you have no running concerns, you should be fine to wait awhile before having the codes read and a repair made.

Share this post


Link to post
Share on other sites

Just had it checked and the error is P0300 on cylinder 6, according to what I was told it is a random miss. Before someone suggests plugs and wires, I already tried that last week.

I had it scanned at Auto Value and the guy who scanned it said since I already changed wires it could be a sticky injector. Does that sound valid?

I am running some seafoam through it now, yes I realize that is a long shot but it sounds easier than cleaning or changing an injector.

Share this post


Link to post
Share on other sites

Well you should have did a cap and rotor along with the plugs and wires.

My truck did this and it was the Cap!

Share this post


Link to post
Share on other sites

I don't think it has a cap on and rotor on that motor. I can't find any reference to a distributor cap and I pretty sure the coil pack don't use a cap and rotor. But good idea though.

Share this post


Link to post
Share on other sites

The 6.0 motor does not use a distributor cap. It has individual coils mounted above the valve covers and a short plug wire to each cylinder. Same set up as the 5.3!

Share this post


Link to post
Share on other sites

Upnorth, Why not swap the #6 coil with an odd number coil (1,3,5,7) to see if the misfire follows the coil?

I will give that a try.

Share this post


Link to post
Share on other sites

Still there. I am trying to eliminate the easy stuff and I am trying to change the fuel filter and of course the dang lines are stuck good. I have been spraying penetrating oil, tapping the nut and trying to loosen it for a couple hours and getting absolutely nowhere except close to stripping the nut mad

Anyone have a surefire tip to get those things loose?

I remember the days when fuel filter was under the hood away from all that fricken corrosion, what were they thinking to moving back by the tank confused

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  

  • Your Responses - Share & Have Fun :)

    • I have not purchases Forscan as I have access to an  OEM scan tool. There are somethings that the Forscan software can do that IDS cannot with Asbuilt. I have ways arround that. Just to clarify, you may not have to purchase the software to do what you want but use their free version. This is worth exploring. As for the OBD interface, might want to ask that question is a specific f150 forum and get an idea of what others are using.    High speed and medium speed compatibility would be nice for future toying. For your truck, you only need high speed interface. I can't remember what pins. Your truck has a gateway module DLC.  Basically it's a router that allows the different networks to communicate, but also your scan tool to communicate with all the networks over HS CAN 1 and 2.   The only software related mod I have done to my car is change the 3 turn signal blinks to 4.   Happy modding!
    • Ok that makes sense. When I saw swan I figured it was an member id. When I went to cub today I asked the HS kid if they had any  I got "I know we have them I just don't know where they'd be". I said freezers maybe by the other tots he said "what makes you think that" You can't make it up!
    • I think Schwan's is what was meant.   https://www.schwans.com/products/product?id=60297   The operator person will bring them right to your abode.  
    • icefishinnut gets 2nd win with a 301 score.. 2--rl_sd                     298 3--BlackLundProV  293 4--Fishing_Novice   285 5--mnwildman         284 6--Juneau4               282 7--Swiveldigger       275 8--huckfin                 274 9--Rip_Some_Lip     244 ___________________________________________________ SEASON TOTALS 1--Fishing_Novice           5274 2--BlackLundProV           5126 3--huckfin                         5094 4--Juneau4                       5076 5--Rip_Some_Lip              4952 6--Swiveldigger                4876 7--rl_sd                              4825 8--icefishinnut                  4804 9--mnwildman                  4780
    • Box? i don't think I've ever seen them but will be looking in a little while
    • Buy a box of cheesy tots.  Cook.   Use rack over sheet pan on grill or in oven.  😀
    • Cheesy tots sound great! Anyone got a recipe?
    • If you're feeling adventurous some time follow the same process you just explained but instead of using a rib rub try using a generous amount of Montreal Chicken seasoning with yellow mustard as your glue.  Also, try a wing or thigh before using the Famous Dave sauce.   Goof Luck
    • I took wings, thighs and legs and put rib rub on them and let them sit for 4 hours then I smoked them for about 90 minutes this morning. Tonight I put them on the grill to crisp up and slathered with Famous Dave's. I seem to kill chicken on the grill but with the smoker I can regulate better plus all that flavor. Only way I'll do chicken now!
    • The grain belt is a bigger sin.😁
×