Jump to content
  • RECEIVE THE GIFTS MEMBERS SHARE WITH YOU HERE...THEN...CREATE SOMETHING TO ENCHANT OTHERS THAT YOU WANT TO SHARE

    You know what we all love...

    When you enchant people, you fill them with delight and yourself in return. Have Fun!!!

Sign in to follow this  
LakeTahoe

175 Verado - Overheating?

Recommended Posts

2007 Verado 175 - anyone with Smartcraft ever have an overheat alarm go off?

Had it happen twice... we shut it down, started it again, and it ran fine the rest of the day? Ran perfect other than that?!

LT

Share this post


Link to post
Share on other sites

I have an Opti with Smartcraft gauges. It has shut down on me 2 or 3 times for the overheat alarm ---- every time was in summer on Lake Minnetonka and the lower unit picked up enough floating weed debris to partially block the water intake. One time I had to kick the boat into reverse to clear off the weed debris, the other times it fell off by itself when the boat shut down. Like you said, runs perfectly as soon as the weeds are gone smile

Share this post


Link to post
Share on other sites

LT,

This may or may not be the case in your situation but with a Verado there are a couple of things you need to make sure you do.

This is off of the Verdao Owners HSOforum:

1 If you store your engines in the tilted up position, give

them a couple minutes to settle down when you tilt them down to start. We have 2 instances where people who stored them up were immediately starting when tilting down and oil got past the breather and into the supercharger and it went bye-bye. The SC’s have an oil passage drain that works well if you wait a minute or two before starting. It’s probably also a good thing not to have the motors at the maximum fill point or overfilled

as this exacerbates the situation. If you get blue smoke, shut them off immediately and wait a few minutes.

At any time: WHITE SMOKE = NORMAL ,BLUE SMOKE = BAD

2 When switching the motors on, click one notch and wait until the sensor beep is over before cranking. That insures your start up check is done. Not stopping at this step and going straight to the start will sometimes confuse the engine. It might quit on you 5 -10 min later and issue a “check engine” fault.

Hope this helps.

Bob

Share this post


Link to post
Share on other sites

Thanks for the responses... (Da Break) I actually read that on the Verado site as well, and have followed those procedures. I ended up bringing to the dealer anyways and they're telling me absolutely that nothing is wrong, that everything is in perfect working condition. That's good, I guess, but what's the point of alarms if nothing is wrong? (just a rhetorical question).

Share this post


Link to post
Share on other sites

My Opti did the overheat alarm last night, first time this year. We had been bass fishing (yuck) in the shallow slop (yuck). Drove out of there and only went a little ways before it started overheating. Reverse didn't clear the weeds, so with the boat drifting and the motor off I tilted it out of the water to clear the weeds. After that no more problem. If you monitor your temp on your Smartcraft you will see it drop like a rock as soon as you get the weeds off.

Share this post


Link to post
Share on other sites

LT,

One other thing I thought of. I have a 225 V-Rod, and I got a service recall notice from Merc last fall to bring it in for a flash upgrade to one of the modules on the motor. I'm not sure which one, but I believe it was to cure unwarranted alarms and shut down.

Bob

Share this post


Link to post
Share on other sites

Yep, I told the dealer that too... they said the reflash was done already... they cleared all the codes and test drove, everything looks good, and Mercury took care of the labor for me! I've always heard their customer service was good!

Thanks for all the suggestions.

LT

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  

  • Your Responses - Share & Have Fun :)

    • We are still going to put a piece along the bottom but I’m not a fan of diamond plate so we are going to try some annondized aluminum.    We were going to get some decals for the side but I was starting to like the plain look so we just went with some small things for now.  I think that about wraps up the outside and I think I have to quit for the night people weren’t kidding when they say writing these up takes awhile. I’ll post the inside stuff tomorrow. 
    • Next up was prepping the studs for the VHB tape. I scratched up each stud with a fine wire wheel attached to a drill then wiped clean with isopropyl. We went with 1/2” VHB tape since we got it for next to nothing. Around the windows and some other areas we did two strips of tape to cover the whole stud but most of the studs that were just getting sheeting we did one strip. I would recommend the 1” though it would be a lot faster.  people are not kidding when they say there are no second chance. The corner piece that is sitting inside had to be kicked off and we never even pressed on it. Good thing we had one extra sheet but no more mistakes could happen after that. The place we were working at had a bender we could use to get our corner bends which worked out great.  The windows are from menards. I custom ordered them which turned out to be cheaper than buying the stock jeldwen ones which didn’t come in the sizes we wanted. The first shipment of windows came in and when I went to pick them up two of the 4 had cracked glass and the guy working goes “so you don’t want these?” I was like no I don’t want a broken window. So we had to go and re order new ones. Two weeks go by and I realized I never got an email confirming my order so I went back in to check on the status of my order and the guy said they never got reordered. At this point I almost lost hope in all of humanity but tried to stay calm. Finally got all the windows installed and the siding put on.  We wanted to try and do rounded wheel well so the picture above is prior to trimming the edges.  We tried using the 1/4” HDPE plastic sheets which looked pretty good. The next day when the sun hit that wheel well it expanded out about 3”. I wanted to screw it down and see if that helped control where it expanded but my brother wanted to scrap that idea. We ended up just using some steel sheeting and welded it up. All the corners and seems where water could get in was welded and then the whole wheel well was welded to the wall studs and a little bit of the frame.    Since the wheel well sees a lot of snow and salt we wanted it to be durable. The Berliner stuff you can buy usually doesn’t hold up so we brought it to a guy and had it sprayed. He said it should last forever and if we ever have any issues just bring it in and they will fix if.  I think they turned out pretty good and I think the rounded look is just something different than the traditional square wheel well.    Our door came from FishnStyle in shakopee, they sell firebrand so this is the same door they use. It’s made by a company called challenger doors.   We cut a piece of aluminum sheeting so it would fit perfectly over the white color it came with. We used the thin VHB seam tape to attach the aluminum sheet to the white aluminum skin of the door. Only other thing we had to do was cut our a small hole so the door handle could go through. The whole door is held on by VHB tape and I also threw in a couple of stainless self tappers since the door came with pre-drilled holes.    For the roof we did a one piece aluminum roof held on by VHB tape. I guess I didn’t take a picture of that but we got it from a local semi trailer repair company in Blaine for a couple hundred bucks  The roof trim is 3”x1/4” aluminum flat stock and the trailer lights are mounted to that. 
    • If the price was right and your happy!👍✌️
    • Next up was cutting all the 2”x1” tubing. My brother picked up this little bandsaw off hsolist that worked pretty well. Using sketch up was great, everything could be laid out and you knew exactly what length to cut everything.    Once everything was cut we started welding it up. Built each wall on saw horses and once we got to the last wall we finally had a system down, go figure.    once we got all the walls made we leveled out the frame. Had to add a bunch of weight to the back to try and get it flat. This is where I wish we had a flat driveway. After we got everything good and level we started welding the walls to the frame and to each other.    The next day was the roof. From looking at other builds I thought people were just running one piece of tubing across and just attaching to the two sides but as we found out that does not work. We tried that and the top of each side wall had way to much of a wavy look. Closer look at other builds looks like people made the roof the same as the walls on some saw horses so everything was square and then set it in between all the outer walls. We ended up doing something similar but we turned the inside roof length piece on its side so it was more of a strong back which minimized any waviness of the tubing. 
    • We were "missing" a few pieces of chicken between the time we took them out of the smoker and put them on the grill with the BBQ sauce. They vanished, I swear!
    • Figured I would post me and my brothers build on here since this is where I got most of the information from. Thanks to lipripper for posting his builds and answering questions. I pretty much based the house off of his with a couple of my own tweaks. Im not sure how pictures are posted on this it’s looking like they will all be at the end of my post so maybe I’ll start with one post then keep adding to it so the pictures stay in some order ( I was bad at taking pictures so I probably missed some stuff) So here we go...   The frame is a Berkon 21’ with a 4’ V galvanized. We called berkon and the guy said they had one frame left and it was $700 cheaper than normal price since they were changing something for ice castle so we put money down to hold it then he called and said ice castle needed it but they were going to make us a new one (this was the start of our struggles). Which actually worked out nice since we could move some bracing around and move the hydraulic pump to a different spot. We had them move the back center brace so we could have 3 holes between our couches similar to papabear. We  thought about doing aluminum but the guy at berkon said the weight savings would only be about 700 lbs and I personally don’t like how aluminum seems to get brittle in the cold.  Prior to getting the frame I tried to order as much stuff as I could think of like others have said to do but since this was our first fish house I wasn’t 100% sure on everything. I used google sketch to layout the studs and the windows. Hoping everything would work out as planned. 
    • Spring only for me, when Orioles first return. Mine never get hit much. 
    • Not sure if somebody put a lot of time in to make this or if it was something Arctic Cat made. I could see someone pulling this around Hay Days.Thought it was just to cool to pass up. 
    • Whatever trades they might make won’t be to make a run. It’s going to be to rebuild. I guess there’s still some interest in Dozier from a couple teams, but otherwise, we don’t have much trade value in anyone. I’m just still hoping we finish .500.
×