Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. 😀

  • Connect, BE BRAVE - We Share Fishing Reports & Outdoor Information Here

    "Post Your Thoughts" - Share a wee bit and Help, please...

    Because you want others to share great outdoor information with you!!!! Share what you 'love about your area' in the outdoors.

    EMOJI those posts you 'appreciate, please.'

      Have Fun!!!

Sign in to follow this  
Mr55371

Auger Sharpening

Recommended Posts

I see Strikemaster has a blade sharpener for their augers. It looks a whole lot like the one one I already had in my tool box. Small had held job with a V shaped sharpening jib. So in my infinite wisdom, I put it to work on my blades and headed out on the ice. The results were far from what I was expecting. I'd have done better to try to punch a hole with the handle. Is this Strikemaster sharpener different from these regular blade sharpeners...? I think I may just do better to buy new blades each season.

[This message has been edited by Mr55371 (edited 12-27-2003).]

Share this post


Link to post
Share on other sites

I just baught one myself. I think it works great. I think it's extremely important to use it in the right direction. If you look at the sharpener, one side has a flat piece of steel and the other side has the sharpener. You need to make sure that sharpener is used only on the beveled side of the blade and never on the flat side of the blade. It's also important to keep the steel piece flush on the flat side of the blade. Another point, the sharpener probably won't fix a blade in real bad shape. The sharpener is to maintain a sharp blade after every 4-5 uses. Hope this helps.

Share this post


Link to post
Share on other sites
Guest

I have one and it seems pretty good for keeping the edge but wont bring back a banged up one.
Fishermans corner has regrinds for about 6-9 bucks w/exchange and they work as good as new. keeping them clean is a must also, rust will ruin the blade and it will be hard to keep an edge.

------------------
en kala
(I fish)

Share this post


Link to post
Share on other sites

The V-sharpeners tend to take too much meat/steel off the blade.

The trick is ONLY hone the TOP edge, NEVER the bottom.

I do mine now with a 5" diamond impregnated hone made for sharpening arrows. I just work the top edge with the stone in a semicircular fashion, paying close attention to the angle. This has been very good to me this season on my hand auger. So far I have not managed to trash a set of shaver blades.

I trashed a set last year with a V-sharpener, took too much off the bottom and they are completely worthless. Honing only the top is the trick with shavers.

------------------
Ed "Backwater Eddy" Carlson

Backwater Guiding
"ED on the RED"
[email protected]
><,sUMo,>

Share this post


Link to post
Share on other sites

I use a regular mill file to sharpen my auger blade and it works great. You also have to keep the point on the end of the shaft sharp, because that acts kinda like a pilot hole for the main blade.

Share this post


Link to post
Share on other sites

I have the bait shop do mine, and yes he does the center point too, wow what a diff., just like new now. He charges $10. its worth it for me I can usally get 2-years out of a sharpning, if I watch where I drill.

Share this post


Link to post
Share on other sites
Guest

Exchanging my dull blades for ones that have been sharpened is exactly what I like to do. Is there anyplace in the LOW area where you can do this? I live in Warroad. frozenminnow-Where is Fisherman's Corner?

------------------
DIRTBALL2

Share this post


Link to post
Share on other sites

Fishermans Corner is in Pike Lake just north of Duluth. I find it easiest and more time effective to carry extra blades and exchange as needed.

Share this post


Link to post
Share on other sites

Thanks for the input. I took the sharpener to the blades again and they work good once again. Funny what a little bit of knowledge does for you, eh...?

Share this post


Link to post
Share on other sites
Guest

Fishermans corner is in Duluth (Hermantown) on Highway 53 ph. 218-729-5369 I dont know but they may do phone orders, they are very helpful folks at this store.
good luck.

------------------
en kala
(I fish)

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  



  • Your Responses - Share & Have Fun :)

    • And they still come out with that product! 🙃
    • I ran my last set of hankook dynapro ATM tires for 94,000 and wasn't at the 3/32 wear mark. Just wanted to get a new set before I started grad school. 40k on my current set without issues. I rotated mine every 7500 miles. I have a friend who got 103,000 out of his set. I know people will call BS but I have no reason to lie and no incentive. Both were on half ton chev trucks and I took mine down some super sketchy farm roads that were previously flooded and some flooded logging roads. It's the only tire I'll buy and their fairly affordable. Also a good alignment goes a long ways in the longevity of tires
    • So..............when do pitcher's and catcher's report to spring training?
    • Wine, rum and Woodford 🙄
    • Do they drink Wine while cooking like our ladies?  😋
    • I just put on a set of Falken Wildpeak ATW3 before hunting season and have been impressed so far. The only problem is I don’t have anything to compare against because they replaced the factory tires on my pickup that were 6 years old. I wanted a little more aggressive tire than the factory tires and these seemed to fit that description. I only put about 7-8k miles on my pickup a year so it’s going to take a while to find out for sure how they are in the wrong run but I am happy so far and the price on these tires was great. 
    • I guarantee they are all hand made. 50 lbs of dipping chocolate 10 lbs of white chocolate, mass quantities of sugar, coconut and fondant. Then 13 women put in 8 hours of mixing, rolling, dipping and trimming. Each family has some of the centers mixed ahead of time because they need to cool and set overnight.
    • check out the smith lift it is expensive but they work.
    • Thanks again.  Now the issue is how do you tell someone that the ideas she has are wrong.  She has never accepted advice from me.  Maybe I should have one of you guys contact her.  No, actually I wouldn't do that to anyone.
    • anyone find a lighter alternative to the ice castle tables? the thing can be a PITA to move and align
×
×
  • Create New...