Jump to content
  • RECEIVE THE GIFTS MEMBERS SHARE WITH YOU HERE...THEN...CREATE SOMETHING TO ENCHANT OTHERS THAT YOU WANT TO SHARE

    You know what we all love...

    When you enchant people, you fill them with delight and yourself in return. Have Fun!!!

Sign in to follow this  
DRH1175

Impeller/ Water problem

Recommended Posts

How do you know when the impeller has to be replaced. We have a 2005 4 stroke 25 hp Nissan that we took apart today. The impeller looks good. But how do you know? The issue only a trickle to drops of steam of water comes out of the motor when is running.Almost a sputter to a very week stream. We dropped the lower unit and looked at the impeller. Blew out all lines nothing seems to be caught anywhere. No water is getting to the Thermostat. We took that housing off And ran the motor in water. Not even a drop of water was getting to the thermostat. Now would this be the impeller or something else that would be causing this?

Share this post


Link to post
Share on other sites

Just by looking at it, it shouldn't have nicks or cuts in it and it should look really bent. Is the key still in it? If not, the shaft could be spinning, but the impeller could be just sitting there doing nothing or barely spinning.

Your intake screens may be plugged.

Is there noticable wear in the impellers backing plate? If so water could be bypassing the impeller.

Share this post


Link to post
Share on other sites

The vanes on the impeller need to be straight, not curved. What does the pump housing insert look like?

Share this post


Link to post
Share on other sites

I've never worked on a nissan. If they need to be straight and not curved it's my bad for giving that chunk of bad info. However, I find that interesting. I've never seen a centrifugal pump with straight impeller vanes, and I've worked on an awful lot of them.

Learn something new every day.

Share this post


Link to post
Share on other sites

Look at a brand new impeller, it has straight vanes. Over time they will take on a curved shaped. Especially from sitting the winter. The impeller itself does not sit exactly in the center of the housing. If it is too curved it will not pump efficiently.

If the impeller were exactly in the center of the housing, it would turn with the drive shaft, spinning water within the housing, but it would not pump water.

However, it is designed with an offset impeller. When the impeller turns, it has a lot of room on one side of the pump, and not much room on the other. As the drive shaft and impeller spin, water enters on the side that has a lot of room, and is pressured out on the side that doesn’t have much room. I rambled a bit there didn't I

Share this post


Link to post
Share on other sites

When you reassembled the motor did you pay attention to line up correctly the water tube ? Sometimes it gets line dup crooked and breaks or doesn't allow any flow up to the motor.

My bet is on the key, it's been lost, shaft spins but not the impeller, very common issue.

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  

  • Your Responses - Share & Have Fun :)

    • heard from 2 folks who went the other day, their boat not good the other good!!  go figure..  same charter company...
    • Nice fish.  Heading out to Lake Michigan in 2-3 weeks.  Haven't decided exactly where yet.
    • We were on Kinn's boats out of Algoma.  
    • What port did you head out of Duff?
    • A group of us are planning on getting together on Lake Osakis for the day on 8/18/18 for a day of fishing and a midday picnic at the Battle Point Park.  We would enjoy connecting with some fellow anglers from the site to connect and have some fun.  Osakis is a great lake for big gills, slab crappies, nice walleye, pike, smallmouth and largemouth bass.  The best walleye bite has been during low light periods.  Sunfish and crappie bite all day.  We plan on taking a break around noon at the Battle Point Park for lunch.  Right now tentatively looking to connect around 8-9 at the access.  Otherwise look for a red and white Warrior and connect with me, "Borch" on the water I'd you'd like.   I might even have a fishing report really fresh fishing report for you. 
    • It was slow for us this year, steelhead on Sunday afternoon, and only a couple nice kings on Monday. But the potential for a big fish is there again this year.   My friend is a little on the small side, always makes nice fish look HUGE.   My early morning fish came in at 23.6 lbs. A pound and a half heavier than the top pic.      
    • Nice work, that looks incredible. And I'm a big fan of the grey motif.   Thanks for the show and write up.
    • Yeah we brought it up to our cabin and sleep in it if there are a bunch of people up there. Thanks!
    • Are you guys using it as a summer camper as well?  Super Product right there!  😎
    • Thanks! It weighed in over what I thought which was disappointing. It was right around 7000 lbs with full propane tanks and some other stuff in it. We actually weighed it just after getting spray foamed and it was already at like 5000 lbs I’m not sure how others that did the same style steel stud house have a finished weight around 5500 lbs.    The cost in materials was above 20K but below 25 still too scared to finish adding the receipts. We really tried to use the best materials we could find and not cut any corners. When I was pricing stuff out before we started my ballpark was 19K but I forgot to add a tv screws wire and little stuff like that.    Yeah it took a lot of time but I enjoyed it for the most part. I’m actually getting kind of bored now and don’t know what to do with all the free time. 
×