Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. 😀

  • RECEIVE THE GIFTS MEMBERS SHARE WITH YOU HERE...THEN...CREATE SOMETHING TO ENCHANT OTHERS THAT YOU WANT TO SHARE

    You know what we all love...

    When you enchant people, you fill them with delight and yourself in return. Have Fun!!!

Sign in to follow this  
jonnyICE-MAN

Light ?

Recommended Posts

I recently puchased a Yamha Grizzly 660 with the county plow. Problem is running it at night(the plow blocks my headlights when up). Question is can I just buy 12v fog lights? Cause are'nt fourwheelers 6v? confused.gif Thanks in advance.

Share this post


Link to post
Share on other sites

I am not sure on the yamaha, I have a 07 cat and I have installed 2 running lights on the front of it and one on the back of the machine, mine is 12v but again I am not sure on the yamaha!!! Just give your dealer a call and see if you can install lights on your machine they should be able to help you out!!!

Perchjr

Share this post


Link to post
Share on other sites

Thanks for the replies guy's, now I have another project smile.gif.

Any idea what way would be the best to wire it, straight to the battery or is there a better or easier way?

Share this post


Link to post
Share on other sites

For my light's I just went to the coil under the seat and used a in-line fuse and it has worked ever since!!! Again it wouldn't be a bad idea to call your dealer to see if the electronics are a little tricky when it comes to installing light's!!!

Perchjr

Share this post


Link to post
Share on other sites

Be careful about how much stress you put on the charging

system. 12 volt fog lights are 55 watts apiece so you

are adding an extra 110 watts to the system.

As stated above call the dealer

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  

  • Your Responses - Share & Have Fun :)

    • Yes, its a 110v motor. I would've preferred 12v also but not a big deal since all my 110v outlets can be fed from an inverter so they are powered whether the generator is running or not. I think what you mentioned with the single shaft between them will be the ticket. Looking forward to seeing what you come up with.
    • When I was a kid, we came across a small flock of pigeons along a railroad track while grouse hunting. Shot three and my mom put them in a crockpot with other ingredients and, although I prefer grouse, they weren’t bad. 
    • You should get the 30 amp power cord if you don't have one already. You can use the 30 amp power cord adapter(30 amp female to 15 amp male) for home use. Otherwise when at the campground plug the 30 amp power cord into the 30 amp receptacle.  Now your set for any situation.     Your 20 amp receptacle is protecting the wire from receptacle to breaker panel. Besides running the AC, your running a refrigerator, 110v receptacles, and convertor.  A 16 gauge extension cord is no good.  
    • I had a contractor do my garage floor.  Here is the work order and quoted amount.   Work To Be Done:
      *Epoxy concrete garage floor. (784sq.ft.)
      -­‐Shot blast surface of floor.  (Work  Shop area) -­‐Light acid wash over existing floor, let dry over night.
      -­‐Apply primer coat of commercial grade epoxy. (4mil 650 Armor seal)
      -­‐Apply flakes to primer coat, 100% coverage. (4mil)
      -­‐Shop Vac. Up flakes that didn’t adhere to the floor. (Colors will be gray and red in color)
      -­‐Apply coat of clear commercial grade epoxy.  (4mil)
      -­‐Final coat of Armor seal 650-­‐sealer coat. (2mil)
      -­‐Cure time-­‐ 24 hours for foot traffic and 72 hours for vehicle traffic before use.
      Total Cost: $3,400
    • I did see Menard's had the 0 Degree when I was in there last night.  Not sure what kind of tip connection you may have though?  A last resort if you have a Dremel tool is to try and auger it out with one of their metal tips?  But that may be a long-many Beer day! 🤤
    • I feel like if the power washer works, it's going to be the easiest and most fun way of removing that stuff.     $7 on Amazon.  
    • 💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰💰
    • its a ice castle ac unit; i believe the running watts are 1200-1400; nothing else would be running off this outlet; and i believe i purchased a 12guage cord to keep it plugged in to maintain the deep cycle battery and to provide power.   this also raises another question then... am I ok using a standard (16 guage perhaps?) extension cord to connect to the power source at campsites? If not, I should probably replace this...
    • Please don't do this! I have no problem running my camper ac off a 20 amp outlet!
    • You can but it would be much easier if you had some help. Biggest thing is to open the clamps up so it can sit on the boat quicker and give your arms a break.  I swapped out an 18HP for a 35HP and it was like trying to carry a 100lb sack of potatoes. Got it done but heavy. Today I would not even think of doing it myself but back then I was a little more hard headed. I am also assuming its a tiller with no controls to hook up. I would guess it will be around 125lbs according to Yamahas site.
×