Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. 😀

  • RECEIVE THE GIFTS MEMBERS SHARE WITH YOU HERE...THEN...CREATE SOMETHING TO ENCHANT OTHERS THAT YOU WANT TO SHARE

    You know what we all love...

    When you enchant people, you fill them with delight and yourself in return. Have Fun!!!

rundrave

Connect Iphone To Old Receiver

Recommended Posts

I want to connect my iPhone to an old home theater receiver in my garage I am sure there is lots of ways to do this just trying to think of what would be best.

 

I have an iPhone with no headphone jack. Not a problem I currently put it on a dock with a speaker. That dock has a 3.5mm out that I should be able to convert into something that would work as an input to the receiver?

D9D49849-ECD3-4B0E-B7B9-9040ACEAAD51.jpeg

F0DE32E6-663E-406A-806A-AA4EDE0B4C04.jpeg

 

 

Here is the back of the receiver, its an old ONKYO that I had set up as a home theater many years ago. Its been collecting dust in the basement and I still have all of the speakers so I thought, hey I could really jam out in the man cave with some good speakers if I can get everything hooked up correctly

 

I could go 3.5mm to rca (red and white) and I think that would get me stereo and not mono?

 

Or could I go 3.5mm to digital optical or 3.5mm to coaxial? See all my options circled in red below?

3355DACC-8506-47BF-9F84-3CE2AA470FAA.jpeg

 

 

 

Share this post


Link to post
Share on other sites

ok I got it figured out, not sure its the best solution but it works.

 

I thought the 3.5mm jack on the jbl speaker was an output, but its an input so completely scrapped that. I was hoping to go that route so it would charge my phone at the same time.

 

So instead I opted for this option instead:

 

 

It works and I have left and right stereo and its not mono. It sounds ok but I may splurge for a 3.5mm to  digital input cable and see if its worth it.

AC9C2DC6-C74E-4F54-BF27-9DEF9F3772E6.jpeg

Share this post


Link to post
Share on other sites

Find this on Amazon and you can use Bluetooth. It has 2 different outputs. 3.5mm and RCA:

 

Logitech Bluetooth Audio Adapter for Bluetooth Streaming

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




  • Your Responses - Share & Have Fun :)

    • All you guys still don't get it.   I didn't explain it well enough.    There are three batteries, each can hold 80 Amp hours.      When the 24 volt motor is in use, two of the batteries use some of their capacity, equal for each battery.   So let's say you use 10 amps for two hours.   Now you have two batteries with 60 and one with 80.   Run all three (36 volt motor) for 6 hours at 10 and two batteries will be totally discharged and one will still have some charge.   Any further current draw will potentially damage the two batteries that are totally discharged.      Of course the 36 volt motor will probably quit working as soon as two of the batteries are flat, but the concern is there.
    • pulled the sled out, turned the key after putting in fresh gas, and it fired up spot on. seems to want to go, as it jumped at a little throttle, bring on the snow, its ready.
    • Del is correct 3ea 12v batteries in series are required to get 36v. 2 in series to get 24v and each battery 12v. You can connect a + and - wire to each individual battery, while wired in series, and run 3 separate 12v isolated devices. A + and - to either of 2 in series gives you 24v.   You NEED a "3 bank marine charger" which has 3+ and 3- charging wires which charges the 3 batteries independent of each battery. When one battery reaches full charge, that bank shuts off other 2 banks continue to charge until respective batteries are fully charged. Batteries will not overcharge.    You can run both 36v and 24v motors on a 3 in series batteries but DON'T run both at the same time. Current draw on the 2 24v batteries will greatly reduce battery life and under serve current on the 36v motor.   Best solution is separate battery banks and chargers for each motor and a separate 12v for starting motor and running 12v electronics.    Suggestion, carry a set of jumper cables long enough to reach from the battery bank to your primary motor battery. If your starter battery dies 5 miles off shore, just jumper to any one of the trolling motor batteries to start your engine.
    • Well that game went about as expected. Was worse for me, because my directv went out, so I had to listen to the game. Couple plays I wish they would have done differently...go for the touchdown at the end of the first half, instead of field goal. And when it was 4th down midway through the 4th quarter, they should have kicked the field goal instead of going for it. Was fun having a top ten ranking while it lasted. That loss guaranteed gameday won’t be here for Wisconsin game.
    • You definitely want a salt shield as it will keep SOME slush gravel  etc off of the sleds but plenty still comes over so you want to have a quality cover on your sled to
    • I have wondered what happens to those mallards that the kids feed bread to all summer on Vermilion when duck season starts...  Summer... walk out on the dock and here they come....  Fall ????
    • All the corn I have starts with an A.  And I have plenty of them.  A couple houses hung too.  Spose I should put the Free Food and Lodging sign And get some more takers. 🌰🦆👨‍🍳
×
×
  • Create New...