Jump to content
  • GUESTS

    If you want access to members only forums on HSO, you will gain access only when you Sign-in or Sign-Up .

    This box will disappear once you are signed in as a member. 😀

  • Connect, BE BRAVE - We Share Fishing Reports & Outdoor Information Here


            TURKEY CONTEST "Post Your Thoughts" - Leave YOUR mark, make each place you visit "a little better"! Post please......

        HSO Turkey Contest - Sign-up by April 1st. - Click Here.

        EMOJI those posts you 'appreciate, please...IF YOU WANT MORE LIKE IT HERE..'

        Have Fun!!!

Sign in to follow this  
Sy

Gun Club or place for shooting a shotgun

Recommended Posts

My brother has a cabin near Webb Lake that I am heading up to in a few weeks and I was trying to find a place near there that we can shoot shotguns. I have been hunting most of my life but he has not and is going pheasant hunting this year so he asked if I would take him out to practice. In places I normally hunt I know of old gravel pits or public land where I can set up some targets and shoot but I don't know if there is any place like that near Webb Lake. If not, are there any public gun clubs that someone knows about in that area?

Thanks a lot.

Share this post


Link to post
Share on other sites

The Grantsburg Rod and Gun club always used to have open trap and skeet shooting on Thursday evenings. I think you have to buy a membership, but it's only like 20 bucks. Kind of a haul from Webb Lake.

The Fishbowl Sportsmen's on Hwy 35 between Siren and Webster is closer to Webb Lake, but I'm not sure what they have for open trap shooting, you'd have to call them.

Coyland Creek, east of Siren, has sporting clays course.

Share this post


Link to post
Share on other sites

Doesn't sound like any great public land options so I will check out those gun clubs. I appreciate the replies and hope one of them works out. Thanks!

Share this post


Link to post
Share on other sites

Join the conversation

You can post now ↓↓↓ or ask your question and then register. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  



  • Your Responses - Share & Have Fun :)

    • get lottsa oil sunflowers out. they will come.  Just has a fox sparrow fly in.  White thoats and song sparrows should be close behind. 
    • Scare some 50 miles north Eyeguy. 
    • Couple of questions/comments... Check the draw on your AC. I assume that 15amp @ 14 awg will be good enough, but would be good to confirm. Make sure to look at the draw at start up. Have you gotten the 12 ga THNN wire yet? Seems like a lot of the companies tend to oversell the gauge of the wire. It looks like you have overkilled the gauge requirement for most of your DC circuits (i.e. lights) which is good, but if you feel it is lightweight, you might want to step up your furnace and DC outlets again Hard to tell from the schematic, but you are running both ground and positive back to the source correct? I wouldn't start tying ground circuits together. Every connector that you put in a wall is a potential fail. Obviously it is unavoidable for items on the same circuit, but the schematic looks like you are tying grounds across circuits. Just a follow on to the previous comment.... Are you spray foaming or doing batts/foam board? We did spray foam "from the outside in" against the tongue and grove before we sided it. For that reason, we cut PVC and used it as a junction boxed and then taped the ends of the PVC before foaming. All connections occur in these boxes... that way we can get to them "if" some butt connector causes a problem or we need change out something (had a few hold lights fail, and this work awesome to replace) Are you putting your hole lights on a switch? Didn't see one in the drawing Are you using pancake style ceiling lights? I was wondering if you had the capability to turn them off individually if desired. Another comment on the same topic. We put in a 3-way for the ceiling lights so that we have one switch by the entry door and one by the back bunk.... Is definitely nice when the rattle reels go off at 2 am! These are just somethings that we did... along with some things that we should have did - but it looks like you have put a lot of thought into this. It is definitely easier to do things the right way first!
    • Usually first part of may they get here. Tons of finches here yet. And juncos and the regular wood peckers. Hopefully see some cool new ones soon. 
    • Any word on Orioles heading north yet? I'm still a sterile bird void at my feeders. 
    • I'm washing every wall and ceiling in the house .... and it's kickin my butt. Pass the Advil.  
    • Well, something is broken. These links should have worked. It's been strangly inconsistant this way all along. The 2nd and 3rd are from the Ben Harper video already posted so ... yea its broken. Too bad.   https://youtu.be/Wck03Y72340   https://youtu.be/4B-VMr2-228 https://www.youtube.com/watch?v=4B-VMr2-228  
    • Interesting, I found some info online about it.   I went to Rosemount HS.  
    • waytekwire.com has great wire plus other supplies, and is local. Puts regular store wire to shame.
    • Was curious is all,  billy goat was the bridge on parkway. 
  • Topics

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.