Guests - If You want access to member only forums on HSO. You will gain access only when you sign-in or Sign-Up on HotSpotOutdoors.

It's easy - LOOK UPPER right menu.

Sign in to follow this  
Followers 0
harleyharry

Which lake to go to

9 posts in this topic

The wife and I are looking at taking three days to come to Minnesota to fish. I would like to go to a resort that rents perms. I also would like to go on a lake that has a good reputation for perch and walleye

If you were going to take a trip from Michigan, which lake would you go to for the best chance of getting good perch and walleye fishing. We would do this in the middle of the week, as I believe the rates for the lodging and the perm rent are a better bargin.

I read a lot about lake of the woods, milelac and winnie.

Which would you pick? This will probably be a one shot deal, as the fixed income is not what it used to be.

Thank in advance

Harry

Share this post


Link to post
Share on other sites

you can't go wrong with lake of the woods or upper red, both have sleepers. if you have ? about these lakes you can post in there forum.

Share this post


Link to post
Share on other sites

You should get a ton of action on Upper Red...I always pull a bunch of fish out of there.

Share this post


Link to post
Share on other sites

What I like about Lake of the Woods is it's a day time bite. I think your wife might like that too, go out at 8:00 AM and head in at 3:00 PM. Zipple Bay is a good spot but I prefer to go out from the river, either Sportsman's or Riverbend are good choices. I've heard good things about Arnesons and the NW Angle is very good if you don't mind the extra drive and going through a little part of Canada.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now
Sign in to follow this  
Followers 0



  • Posts

    • I apologize if that came out wrong. The idea might very well be the best route to go. It's just that over the past 25 years or so I have seen many attempts to save a dollar that cost a buck and a half to do lol.    Here are my two cents. If you have a slab and you want to pour on top of it while keeping the same footprint that sounds pretty doable and could probably save some money if you don't have to change drain lines, run water, heat runs, electrical etc into the slab.   If you intend to tie into the existing slab and run zones of pex across the joint and have the new and old floors end up at the same elevation it still can be done. Some contractors will not want to mess with tying into and raising the elevation of the slabs and will prefer to start from scratch especially if you as the homeowner want them to warranty the finished product.  The critical thing would be to use enough rebar drilled into the old slab and have enough compaction and sufficient footings to make sure the slabs stay where they are without settling. That would make all kinds of problems with the pex.    Hopefully that response came across better.
    • It'll be interesting to see if the team plays a little harder in front of a different goalie. 
    • Hawg, I'm with you on this one !
    • Check and see if you have a video output on you device. You may be able to record to a digital device.
    • Just use plain old spray paint in a can. I've done it many many times and seems to stick really nice. Nothing special either I can't even tell you the brand because I have no clue. But as mentioned doing 2-3 light coats helps.
    • no expert here, but heat doesn't rise. heat radiates in the direction of least resistance (R value). warm air or water rises because it is less dense than colder air or water.  If you don't insulate you will be heating the ground under your cabin and the earth is a very large heat sink $$$. get some info from an expert in the radiant field as far as tube diameter, spacing, water temp, manifolds, length of runs, and so on. it varies on amount of windows (solar) ceiling height and room type (bed, bath, living area,  storage etc.). once you pour over the tubing you get to live with it. I did my own Home 15 years ago and got some good advise (wish I would have taken it all)
    • Sonar works from above, cameras need to be submerged. What am I missing here?
    • I've also had good luck spray painting PVC.  Biggest thing I found is to do lots of light coats, the PVC makes the paint want to run in a hurry.
    • I believe you can do this with the Lowrance HDS 9 and above.
    • I'll go with another loss in overtime.
  • Our Sponsors