Guests - If You want access to member only forums on HSO. You will gain access only when you sign-in or Sign-Up on HotSpotOutdoors.

It's easy - LOOK UPPER right menu.

Sign in to follow this  
Followers 0
Pikemaster101

throttle cable for auger

5 posts in this topic

Where can I get a new throttle cable with out having to pay $10 for shipping and handling like it is on the home page of the strike master web site.

Share this post


Link to post
Share on other sites

You can go to Big Lake right where Strikmaster is or go to D-Rock in New Brighton. I'm sure they have them, though I would call first. Other than that, check for other service centers.

Share this post


Link to post
Share on other sites

any service center that is certified to do warranty work. Check the strikemaster web sight they can direct you to one near you. If you are close enough to Big Lake, run over there and get one.

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  
Followers 0



  • Posts

    • i'll come hell ya leech!!!!!!!!!!!
    • Bureaucrate-   Correctly me if I'm wrong, weren't you a huge advocate against AIS lawd and allowing the DNR to pull over fishermen and boats for an inspection? But you are okay with them pulling over deer hunters?    Sounds like anything they do, you are against. If they said black, you'd say white...
    • The 2016 Libertarian Party is Starting! Started by Big Dave2, April 12, 2015   Is this post even relative anymore or has it ever really been? May as well just delete it and save some site Band width!
    • Same circuit as the freezer?!! Oh no no no......!!! They kick in at the same time, and  *TRIP* Always have the pump on a separate circuit!!  As mentioned, GFCI is what code calls for, but sometimes dampness will pop one, rare, but I've seen it happen. I nixed the GFCI on mine when I ran a separate circuit for just the pump. That should solve your problem. 
    • I am from Richland Center.
      I have 2 2500 stradics in dis-repair.
      Both bales refuse to return to closed.
      Heard it may be simple as a spring.
      I am kinda cheap….if costs a lot to fix i will buy new reel. Anyone know somewhat local repair person that is reasonable?
    • Well you can't drink all day if you don't start in the morning.  
    • Another one thawing.  made this one for my nephew but will keep it for me. So will have another one in the brine in a couple days. 
    • It's a little early to be hitting the bottle don't you think?  Believe in Trump and you'll feel better.
    • Ok I'll save you from dying. Where can i pick it up? 
    • I use to work on all aluminum body fire trucks.  The only screw, bolt, washer, or nut that we would use was stainless steel as the by using anything else will allow electrolysis to start from dissimilar metals and corrode.  Only problem was the strength of the SS is not as high as regular steel.  Also if you are using SS, i would only use bees wax as a lube.  I use to buy it in a block, and just rub the threads on the screw before putting in the hole.  If you don't, you may find that the threads gall up and strip out.  Then you have issues cause it can be tough to drill out a broken SS screw.  If you have a bunch to do, i found that a combination drill/tap was very useful.  It will drill the hole and tap at one shot.  Here is what they look like.  Good luck. http://www.graybar.com/store/en/gb/combination-drill-tap-bits-22082167?cm_mmc=pla:google-_-googleshopping-_-gb5349-_-22082167&utm_source=google&utm_term=&utm_campaign=Graybar>PLA>Category&utm_medium=cpc&utm_content=fto6JW9w|pcrid|49843833890|pkw||pmt|&gclid=CPzt0MP72tACFYKSfgodC4MH_g
  • Our Sponsors