Guests - If You want access to member only forums on HSO. You will gain access only when you sign-in or Sign-Up on HotSpotOutdoors.

It's easy - LOOK UPPER right menu.

Sign in to follow this  
Followers 0
idratherbefishing

SW MN Walleye Tournament-Sept 20th-Lake Sarah-near Slayton, MN

1 post in this topic

The 2nd Annual Brian "Otter" Lickness Memorial Walleye Tournament will be held Sept 20th on Lake Sarah. This is a great fall walleye lake and a great tourney put on by the South West Minnesota Fishing Club.

Entry Fee is $50 per boat, two fishermen per boat. There will be a mandatory rules meeting and door prizes on Friday Sep 19 at 7pm at the "Grain Exchange" restaurant in Slayton. At least one member of team must attend.

Check in begins at 6:30am at the county park landing on the west side of the lake. Shotgun start at 7:30am and weigh-in is at 2:30pm.

There is a 6 fish limit per boat at any time during the tournament with a minimum size of 15" and only 1 fish over 20".

Prizes based on 50 boats

1st-$800

2nd-$500

3rd-$325

4th-$200

5th-$150

6th-$125

7th-10th - $50

Contact Larry or Angela Anderson at 507-360-3973 or

507-360-8565 for information or questions.

8-23-08 Update: Tourney has been expanded to 60 teams with 6 spots remaining!

Entry may be mailed before Sept 9th to:

SWMFC

P.O. Box 4

Worthington, MN 56187

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  
Followers 0



  • Posts

    • Had an 09'. Got rid of it. Also,  you could not keep the front end aligned.  Otherwise a very nice truck.
    • Helps when I comprehend what I read.  I actually just cut the handle off my tongue jack on my Yetti and welded on 3/4 nut too.  My M18 drill with 1,200 in-lbs (2704-20) and it has no problem raising or lowering the tongue.  Biggest thing I noticed was making sure my drill was on the #1 low speed setting.      As far as torque goes and harming your auger.  I think you are totally fine and shouldn't harm anything.  The max amount that these K-Drills and Clam plates are drilling these days with the big drills are 8".  Most sized augers these days have no problem turning a 10" auger which is nearly twice as large of an area than an 8" auger.  Being 2 strokes can normally operate in any orientation without being damaged the only concern I would have would be your gears and any shifting of grease inside operating the auger head on its side under load.    They say Ions will do 10" holes but after I talked to their customer service reps about it, I wouldn't trust an Ion with a 10" more than I do a wet fart.  Just the fact that they don't even sell a 10" package indicates there could possibly be issues with torque and reliability when operating the 10" auger "accessory".  For now I'd just stick to your strike master going up and save your Ion any extra wear and tear.  Maybe even ask Santa for some electric jacks this Christmas
    • As the media begins to draw a pretty picture about the November jobs report, namely that unemployment has dropped to 4.6 percent, its lowest level in nine years, they are unlikely to tell you the other part of the story. The labor force participation rate continues to decline and is stuck at a rate we haven't seen since February 1978, according to the Bureau of Labor Statistics.  It gets worse. Last month, we lost 4,000 manufacturing jobs, offering more damage to the already 301,000 we've lost since President Obama took office. - Town Hall   See for yourself.. U.S. Dept of Labor / BLS Date Viewer   Whaaa ???   OH, MY....  
    • I wouldn't do that for each one. I was wondering if you couldn't cut a winch down, or maybe just leave it as is, so you could attach a drill to the low speed post and tack weld/rig a socket or something for the other side and just hold it in your hand. It probably won't work because it sounds too easy. 
    • My, such big words!! Yer a talented liddle Smurf, aintcha? We might as well get to work doin' what we were accused of, munchkin!!! Like Carly Simon said, "no one does it better"....  
    • i,ve been falsey accused of inproprieties!!!!!!!!!!!
  • Our Sponsors