Guests - If You want access to member only forums on HSO. You will gain access only when you sign-in or Sign-Up on HotSpotOutdoors.

It's easy - LOOK UPPER right menu.

Sign in to follow this  
Followers 0
ssaamm

shrieking lowrance x-102c

3 posts in this topic

Hello, My x-102c is acting crazy right now. It will run fine an then start making this annoying sound and power itself on/off. It will turn itself to 'chart stopped', and just bounce from screen to screen without being touched. I run through the menu and turn this feature (stop chart) off, and it runs pretty well. Just when I think that I have the problem licked it will do it again. The starting battery that powers it also runs my lms-334c. This 334 runs fine. I moved the 102c to this power source where the 334 is usually at, and it runs in the same sporadic fashion when powered here. I have sent this unit in to Lowrance. For about $200 they fixed it. It's going south again and am starting to lose patience. The power source doesn't appear to be the problem. It usally says that it's reading 11.9-12.5v. I think that this is a workable range. Any thoughts would be appreciated. Thanks Sam

Share this post


Link to post
Share on other sites

I see you are all on the edge of your seats wondering how this has played out. Now my unit will only turn off if I unplug the power chord. I called lowrance, and this very helpful lady is sending me a brand new x520c to replace my x102c that is on the fritz for a 2nd time. I must say I was very surprised and impressed. Go Twins

Share this post


Link to post
Share on other sites

My 332 was giving me trouble, I had to send it in 4 times before they up graded me to 520c. Many hours on the phone with them and all fishing season without a finder! This was under warranty.

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  
Followers 0



  • Posts

    • Helps when I comprehend what I read.  I actually just cut the handle off my tongue jack on my Yetti and welded on 3/4 nut too.  My M18 drill with 1,200 in-lbs (2704-20) and it has no problem raising or lowering the tongue.  Biggest thing I noticed was making sure my drill was on the #1 low speed setting.      As far as torque goes and harming your auger.  I think you are totally fine and shouldn't harm anything.  The max amount that these K-Drills and Clam plates are drilling these days with the big drills are 8".  Most sized augers these days have no problem turning a 10" auger which is nearly twice as large of an area than an 8" auger.  Being 2 strokes can normally operate in any orientation without being damaged the only concern I would have would be your gears and any shifting of grease inside operating the auger head on its side under load.    They say Ions will do 10" holes but after I talked to their customer service reps about it, I wouldn't trust an Ion with a 10" more than I do a wet fart.  Just the fact that they don't even sell a 10" package indicates there could possibly be issues with torque and reliability when operating the 10" auger "accessory".  For now I'd just stick to your strike master going up and save your Ion any extra wear and tear.  Maybe even ask Santa for some electric jacks this Christmas
    • As the media begins to draw a pretty picture about the November jobs report, namely that unemployment has dropped to 4.6 percent, its lowest level in nine years, they are unlikely to tell you the other part of the story. The labor force participation rate continues to decline and is stuck at a rate we haven't seen since February 1978, according to the Bureau of Labor Statistics.  It gets worse. Last month, we lost 4,000 manufacturing jobs, offering more damage to the already 301,000 we've lost since President Obama took office. - Town Hall   See for yourself.. U.S. Dept of Labor / BLS Date Viewer   Whaaa ???   OH, MY....  
    • I wouldn't do that for each one. I was wondering if you couldn't cut a winch down, or maybe just leave it as is, so you could attach a drill to the low speed post and tack weld/rig a socket or something for the other side and just hold it in your hand. It probably won't work because it sounds too easy. 
    • My, such big words!! Yer a talented liddle Smurf, aintcha? We might as well get to work doin' what we were accused of, munchkin!!! Like Carly Simon said, "no one does it better"....  
    • i,ve been falsey accused of inproprieties!!!!!!!!!!!
    • Ken W, I have that book too. Before the internet it was really tough to find info. about sausage making. I never had luck getting a tangy flavor using Fermento. The sausage was very good though.
    • Jacks work very smooth, fresh grease and by hand feels fine for the amount of weight.  I think for the winter we'll just use the gas auger up and the hand drill down.  I don't want to sink another penny into these darn jacks if I can help it, should be swapping out by next year.  I may look into the gear reduction but I feel like trying to throw one of them on each of the jacks could add another 100 that could go toward electric.  leech if you ever stumble on that video post the link so I can see what hes doing different.  Works great on the tongue when it can pivot on the wheels but when lifting the full weight of the house at the back two jack points it just doesnt cut it.
    • I wondered about that when you were building the house. I think you will have to go electric jacks unless you can figure a gear reduction box of some kind. That might be easier than it sounds with some thinking (I hope). Could you mickey mouse the guts of a 2 speed winch? That's a simple gear reduction. Leech, that would have to be a gear reduction box of some kind, right?
  • Our Sponsors