Guests - If You want access to member only forums on HSO. You will gain access only when you Sign-in or Sign-Up on HotSpotOutdoors.

It's easy - LOOK UPPER right menu.

  • RECEIVE THE GIFTS MEMBERS SHARE WITH YOU HERE...THEN...CREATE SOMETHING TO ENCHANT OTHERS THAT YOU WANT TO SHARE

    You know what we all love...

    When you enchant people, you fill them with delight and yourself in return. Have Fun!!!

Sign in to follow this  
vikingmeatwad

Location of serial # on Boat and motor?

Recommended Posts

On the boat it is most likely, as you are standing and looking at the back of the boat from behind it's on the right outside of the boat near the top on the transum. On most motors it's on one side or the other of the motor. It's on the frame that is tight against the transum, or some times it's right under the front of the motor on the frame. Hope this helps. I know the last 2 numbers on the boat serial number is the year it was made.

Share this post


Link to post
Share on other sites

I believe on ours there is also some information on the inside of the motor cover.Either that or it was one of the anti-theft devices...

Share this post


Link to post
Share on other sites

Shouldn't it also be on the U.S. Coast Guard display of capacity yellow display plate, either on the console or near the transom?

nm, that's make and model...my bad.

Share this post


Link to post
Share on other sites

Boat S/N's location should be were others have described it.

Motor S/N Location is somewhat brand dependent. Sometimes they're on a sticker attached to motor mounting bracket (that attachs to the transom), sometimes they're on the motor's midsection where the trim and tilt rams connect to and push against (but on the top side - not the side the trim & tilt works on), sometimes they're under the hood...

marine_man

Share this post


Link to post
Share on other sites

One older boat I had didn't have a serial number. When I registered it, I was told that the state would send me a hull ID but I don't remember if that ever happened.

My Sears cartopper has the SN stamped on the transom.

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  



  • Your Responses - Share & Have Fun :)

    • Good job!  I have never found any Blacks so they look a little different.  Can you take a picture of what they look like cut in half? They look a little scary like False Morel's 
    • I picked for about 2 hours this morning. I'm not exactly haw many I got but its enough for a couple meals. I'm going to chop some of these up and mix with some cream cheese, feta cheese and garlic chives and then stuff some chicken breasts and cook them on the grill. The little bit of rain that we got last week helped the shrooms pop but it really didn't do much else for the woods besides help the mosquito's hatch. There were so many they licked the bug spray off first then swarmed. I found the mushrooms all over, North, South, East and West facing hills. Normally spot 1 has the best results but this trip it was my second spot. All of them had pretty good size too. Only a few that were in direct sunlight were dried up otherwise they are very firm. Spot 1 is the left container. Don't worry, I use a mesh bag while I'm out in the woods!
    • Yup.... 6 & 4 for Lead.... 4 & 2 for steel
    • I ended up framing my house, putting on the T&G , and then spray foaming back against the interior, which may be why I am not seeing any movement... I also used pine vs cedar
    • I agree with the guy who agreed with the other guy.
    • Just wait till they come up with the remote submarine drone with 3d high resolution camera that can see through algae and milfoil and transmit to your eyewear in 3d.   I struggle with properly tying a berkley knot......
    • I agree with rundrave. #4 early and #2 shot later in year
    • Yes, 5/16 T&G I installed last fall. I did the same, but I see this summer it's starting to buckle  
    • Adding a 4th wouldn't do much IMO. The map screen is already too small to be useful when screen is split in 3. I added a Helix 7 G2N to use as a map screen. Networked with other 2 units
    • I could always go and spend more money on an additional unit but some of it is like Floyd said. I have a hard enough time watching one screen. I have the app on my phone. I think that lowrance has the ability to split the screen into 4. I just can't believe I'm the only person who would like to see this but maybe I am. It may not be as big a deal once I get more familiar with the unit. Right now I like to look at all the screens to help discern what it is im seeing on the screen.  I appreciate the input!