Guests - If You want access to member only forums on HSO. You will gain access only when you sign-in or Sign-Up on HotSpotOutdoors.

It's easy - LOOK UPPER right menu.

Sign in to follow this  
Followers 0
cdnfisherman

aluminum boat paint ??

3 posts in this topic

Picked up an old aluminum boat and would like to "camo it up" for duck hunting. Any thoughts on what type of paint will work the best???

Share this post


Link to post
Share on other sites

I painted my Lund S14 and 25 Mariner inside and out last fall with a $40 spray gun from Fleet Farm. It came out looking showroom perfect on my first try.

LUND CAMO PAINT PPG DCC27916
I used PPG'S OMNI PAINT instead of the DCC PAINT. It costs 20-30% LESS
Use self etching primer on all bare aluminum.
Cut back to half recommended hardener and have the people mixing the paint double the flattener. Back up and dry spray the final coat for an ultra flat finish.

Share this post


Link to post
Share on other sites

I was in the same shape with an aluminum jon jon boat here a while back. After a lot of searching I found that Cabelas also sells Duck Boat Paint in the colors you are probably looking for. The best part about it is that the paint is only $26.00 per gallon.

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  
Followers 0



  • Posts

    • LH...I repaired Shimano's for years, and this was a huge issue for the Stradics and the Sahara's, First, look at the bail and make sure that they are not out of alignment. I bet your problem is caused by one part (and it's the probable cause of both problems)..... To keep the bail from rotating on the cast (and snapping shut on you in mid-cast) there's a small friction ring inside the rotor. It looks like a heavy rubber band only it's made of heavy vinyl plastic. It's  actually called a "friction ring". When it goes bad it loosens up just enough to bind up your reel completely and the bail won't snap shut. Also check the round bail return spring with the smal 90* bend in it, that can pop out of the tiny hole (the "bent" end) and cause the bail to do literally nothing. If your bail actuator pin (your :latch") is bent/worn, that will do it, but unikey that it's worn down that much. Loosen up the bail center screws, and see if when they are loose the bail will return. If so, they may be bent/out of alignment. Takes some careful maneuvering to get them back to proper set. I love Shimao stuff, but they never did own up to this problem, as far as I know. Check those things first and let's go from there.

       
    • Look at the diagram, order the parts.   If it pops open or won't close I am still thinking the spring... Take pictures with phone or digital camera as you take it apart.  Helps to get it back together. 
    • Wrong guy there.  I don't fish in MN anymore, don't have a boat either. 
    • Clinton.     After Mn coughed up 66 million for 150 jobs in Cook, nobody from MN ought to be criticizing Indiana.  Looks like they got a heck of a deal.
    • who hasn't done something dumb like that.  I know I have!   good luck making it up to you Mother!!
    • *sigh* Kiss of death my friend............. kiss of death.   LOL
    • make / manufacturer: Eskimo
      model name / number: Mako Upgraded to an electric auger and selling my old one. Runs great and has been well taken care of. Starts on 2-3 pulls every time. I have the extension for it as well as a new set of blades that I bought but haven't needed to change yet. I also have a cabelas auger bag that it fits in.
    • the thing that trips the latch is worn or broken.    i think   will take apart and look if i set hook hard the bail rackets pops up and lets line out won't close some of time...have to do manually
  • Our Sponsors